華為路由交換-靜態路由、浮動路由、默認路由配置

一、搭建實驗環境

R1配置

[R1]interface g0/0/1
[R1-GigabitEthernet0/0/1]ip address 202.100.1.1 255.255.255.0
quit
[R1]interface g0/0/2
[R1-GigabitEthernet0/0/2]ip add 202.100.2.1 255.255.255.0
quit
[R1-GigabitEthernet0/0/1]int lo 0                      //創建環回接口
[R1-LoopBack0]ip add 1.1.1.1 255.255.255.255
[R1-LoopBack0]quit
[R1]display current-configuration interface                   //顯示接口信息

R2配置

[R2]interface g0/0/1
[R2-GigabitEthernet0/0/1]ip add 202.100.1.2 255.255.255.0
[R2-GigabitEthernet0/0/1]int g0/0/0
[R2-GigabitEthernet0/0/0]ip add 202.100.3.2 255.255.255.0
[R2-GigabitEthernet0/0/0]int lo 0
[R2-LoopBack0]ip ad 2.2.2.2 255.255.255.255
[R2-LoopBack0]quit

R3配置

[R3]int g0/0/2
[R3-GigabitEthernet0/0/2]ip add 202.100.2.3 255.255.255.0
[R3-GigabitEthernet0/0/2]int g0/0/0
[R3-GigabitEthernet0/0/0]ip add 202.100.3.3 255.255.255.0
[R3-GigabitEthernet0/0/0]int lo 0
[R3-LoopBack0]ip add 3.3.3.3 255.255.255.255

R1可以ping通202.100.1.2 和202.100.2.3

二、配置靜態路由

[R1]ip route-static 3.3.3.3 255.255.255.255 202.100.2.3 ===添加靜態路由
[R1]ip route-static 202.100.3.0 255.255.255.0 202.100.2.3
R1可以ping通 3.3.3.3和202.100.3.3

三、配置浮動路由

配置備份靜態路由，當 R1 與 R3 之間鏈路出現故障時，可走 R2。
1.配置R1到R2、3的路由

[R2]ip route-static 3.3.3.3 255.255.255.255 202.100.3.3
[R1]ip route-static 202.100.3.0 24 202.100.1.2 preference 80
[R1]ip route-static 3.3.3.3 32 202.100.1.2 preference 80
[R3]ip route-static 202.100.1.0 255.255.255.0 202.100.3.2
配置完畢R1可以tracert 202.100.3.3和3.3.3.3

2.模擬R1與R3之間鏈路出現故障時

[R1]int g0/0/2
[R1-GigabitEthernet0/0/2]shutdown
R1還可以tracert 202.100.3.3和3.3.3.3
[R1]interface g0/0/2
[R1-GigabitEthernet0/0/2]undo shutdown
[R2]ip route-static 0.0.0.0 0.0.0.0 202.100.3.3 ====添加默認路由
R2可以ping 202.100.2.1

四、配置默認路由

配置備份默認路由，當 R2 與 R3 之間鏈路出現故障時，可走 R1。

[R2]ip route-static 0.0.0.0 0.0.0.0 202.100.1.1 preference 80
[R3]ip route-static 0.0.0.0 0.0.0.0 202.100.2.1 preference 80
[R2]int g0/0/0
[R2-GigabitEthernet0/0/0]shut
[R2-GigabitEthernet0/0/0]
R2可以tracert 202.100.2.3