華為交換機配置動態路由OSPF

拓撲圖：

實現步驟：
R1:
 <huawei> system-view                                                    #進入系統視圖
 [Huawei] sysname R1                                                        #設置名稱
 [R1] interface GigabitEthernet 0/0/0                                  #進入接口
 [R1-GigabitEthernet0/0/0] ip address 192.168.1.1 24          #配置接口ip
 [R1-GigabitEthernet0/0/0] q
 [R1] interface Loopback 0                                                  #進入回環接口
 [R1-LoopBack0] ip address 1.1.1.1 32                                #設置回環ip
 [R1-LoopBack0] quit   或  q                                                      #退出環回接口
 [R1] ospf 1 router-id 1.1.1.1                                               #配置ospf編號及私有路由ip
 [R1-ospf-1] area 0                                                             #配置所屬區域
 [R1-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255       #聲明直連路由網段
 [R1-ospf-1-area-0.0.0.0] network 1.1.1.1 0.0.0.0                  #聲明回環ip
 
  R2:
<huawei> system-view
[Huawei] sysname R2
[R2] interface GigabitEthernet 0/0/0
[R2-GigabitEthernet0/0/0] ip address 192.168.1.2 24 或 192.168.1.2 255.255.255.0
[R2-GigabitEthernet0/0/0] interface GigabitEthernet 0/0/1
[R2-GigabitEthernet0/0/1] ip address 192.168.2.1 24
[R2-GigabitEthernet0/0/1] quit
[R2] interface LoopBack 0
[R2-LoopBack0] ip address 2.2.2.2 32
[R2-LoopBack0] quit
[R2] ospf 1 router-id 2.2.2.2
[R2-ospf-1] area 0
[R2-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255
[R2-ospf-1-area-0.0.0.0] area 1
[R2-ospf-1-area-0.0.0.1] network 192.168.2.0 0.0.0.255  # 前面三個0類似於缺省路由 優先進行匹配
[R2-ospf-1-area-0.0.0.1] network 2.2.2.2 0.0.0.0
[R2-ospf-1-area-0.0.0.1] vlink-peer 3.3.3.3                        #定義虛擬連接 相鄰路由id

 R3:
<huawei> system-view 或 sys
[Huawei] sysname R3
[R3] interface GigabitEthernet 0/0/1 或 interface g0/0/1
[R3-GigabitEthernet0/0/1] ip address 192.168.2.2 24
[R3-GigabitEthernet0/0/1] interface g0/0/0
[R3-GigabitEthernet0/0/0] ip address 192.168.3.1 24
[R3-GigabitEthernet0/0/0] quit
[R3] interface Loopback 0
[R3-LoopBack0] ip address 3.3.3.3 32
[R3-LoopBack0] quit
[R3] ospf 1 router-id 3.3.3.3
[R3-ospf-1] area 1
[R3-ospf-1-area-0.0.0.1] network 192.168.2.0 0.0.0.255
[R3-ospf-1-area-0.0.0.1] network 3.3.3.3 0.0.0.0
[R3-ospf-1-area-0.0.0.1] vlink-peer 2.2.2.2
[R3-ospf-1-area-0.0.0.1] quit
[R3-ospf-1] area 2
[R3-ospf-1-area-0.0.0.2] network 192.168.3.0 0.0.0.255
[R3-ospf-1-area-0.0.0.2] quit

R4:
<huawei> system-view
[Huawei] sysname R4
[R4] interface GigabitEthernet 0/0/0 或 inter g0/0/0
[R4-GigabitEthernet0/0/0] ip address 192.168.3.2 24
[R4-GigabitEthernet0/0/0] quit 或 q
[R4] interface Loopback 0
[R4-LoopBack0] ip address 4.4.4.4 32
[R4-LoopBack0] quit
[R4] ospf 1 router-id 4.4.4.4
[R4-ospf-1] area 2
[R4-ospf-1-area-0.0.0.2] network 192.168.3.0 0.0.0.255
[R4-ospf-1-area-0.0.0.2] network 4.4.4.4 0.0.0.0
驗證:
<R1> ping 192.168.3.2               #R1 ping R4

LoopBack

原文鏈接： https://my.oschina.net/xinsui1314x/blog/3057958

掃一掃下面的二維碼，關注我們，獲取更多精彩活動資訊，有好禮相送哦~

微信贊助 微信打賞 支付寶打賞