買了個TL-WDN5200H無線usb網卡,但是發現它居然不支持Linux,但是我有時需要在Linux上使用,這就尷尬了.於是到網上搜索資料,終於解決了這個問題.
- 首先編譯安裝:https://github.com/whitebatman2/rtl8821CU
根據它的README文檔，Ubuntu下可以這樣安裝：
sudo apt-get install dkms
DRV_NAME=rtl8821CU
DRV_VERSION=5.2.5.3
sudo mkdir /usr/src/${DRV_NAME}-${DRV_VERSION}
git archive master | sudo tar -x -C /usr/src/${DRV_NAME}-${DRV_VERSION}
sudo dkms add -m ${DRV_NAME} -v ${DRV_VERSION}
sudo dkms build -m ${DRV_NAME} -v ${DRV_VERSION}
sudo dkms install -m ${DRV_NAME} -v ${DRV_VERSION}
# 下載工程
git clone https://github.com/whitebatman2/rtl8821CU.git
cd rtl8821CU
make
sudo make install
sudo modprobe 8821cu
- 使用
lsusb命令觀察網卡的編號(插拔前后的變化)
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 093a:2510 Pixart Imaging, Inc. Optical Mouse
Bus 001 Device 002: ID 04d9:0223 Holtek Semiconductor, Inc.
Bus 001 Device 013: ID 0bda:1a2b Realtek Semiconductor Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
TL-WDN5200H的編號就是0bda:1a2b.
- 切換usb網卡的模式為無線網卡模式:
sudo usb_modeswitch -KW -v 0bda -p 1a2b
輸出如下:
Take all parameters from the command line
* usb_modeswitch: handle USB devices with multiple modes
* Version 2.5.2 (C) Josua Dietze 2017
* Based on libusb1/libusbx
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x0bda
DefaultProduct= 0x1a2b
StandardEject=1
Look for default devices ...
found USB ID 1d6b:0003
found USB ID 093a:2510
found USB ID 04d9:0223
found USB ID 0bda:1a2b
vendor ID matched
product ID matched
found USB ID 1d6b:0002
Found devices in default mode (1)
Access device 013 on bus 001
Get the current device configuration ...
Current configuration number is 1
Use interface number 0
with class 8
Use endpoints 0x0b (out) and 0x8a (in)
USB description data (for identification)
-------------------------
Manufacturer: Realtek
Product: DISK
Serial No.: not provided
-------------------------
Sending standard EJECT sequence
Looking for active drivers ...
OK, driver detached
Set up interface 0
Use endpoint 0x0b for message sending ...
Trying to send message 1 to endpoint 0x0b ...
OK, message successfully sent
Read the response to message 1 (CSW) ...
Response successfully read (13 bytes), status 1
Trying to send message 2 to endpoint 0x0b ...
OK, message successfully sent
Read the response to message 2 (CSW) ...
Response successfully read (13 bytes), status 0
Trying to send message 3 to endpoint 0x0b ...
Sending the message returned error -1. Try to continue
Read the response to message 3 (CSW) ...
Device seems to have vanished after reading. Good.
Device is gone, skip any further commands
-> Run lsusb to note any changes. Bye!
驚喜的發現無線可用了!