瘦模式 fit 模式不能單獨使用，需要配合無線控制器AC 使用，在fit台數多的時候建議使用，只需要配置無線控制器就可以，配置能夠統一下發到fit-ap上。
胖模式 fat 可以單獨使用，每一個ap都需要配置才可以使用，少量台數建議使用。WEB管理方式就是胖模式.
國內眾多無線AP都采用一鍵切換按鈕，或者均可以通過web方式進入自行修改。而H3C仍然采用國外做法，必須采用console線在超級終端命令行下修改。現在很多的電腦都不帶com口，或者說win7 以后的系統自帶的超級終端都取消了，需要單獨找一個SecureCRTx86來連接。鄙視之。
電腦沒有com口，可以找一個usb-轉232轉換口，當然有的呢還是可以使用。
SecureCRTx86下載地址鏈接: https://pan.baidu.com/s/1ggkgHLx 密碼: dmyb
3CDaemon是一個ftp、tftp服務器工具，也提供下載 鏈接: https://pan.baidu.com/s/1htOGnsw 密碼: hmrp
調試步驟：
1.將無線AP的console口用H3C自帶的console線與電腦的com連接，沒有的與232轉usb連接。注意看電腦設備里的通訊端口是com1或其他。端口設置位/秒 為9600.其他不變默認。
2.打開SecureFXPortable，點連接，最上面第三個新建會話SecureCRT協議選擇Secure。端口就是你電腦里是多少就是多少，如com1,波特率為9600，其他默認。下一步保存即可。
3.看到你的連接里多了一個剛才建立的，右鍵屬性，點選連接串行。端口com1 波特率9600，去掉默認的RTS/CTS,確定保存。
4.右鍵連接終端，將會看到一個經典的黑框。拔掉console再插上或斷開AP電源再開，就可以看到連接上了ap.
****************************************************************************
* *
* H3C WA4320-ACN-E BootWare, Version 1.05 *
* *
****************************************************************************
Copyright (c) 2004-2016 Hangzhou H3C Technologies Co., Ltd.
5.后面就是來通過命令行修改ap了。我將一個h3c技術提供一個錯誤的ap版本bin文件刷固件的錯誤日志貼出來。具體操作一樣。
|Note:the operating device is flash | |<1> Display All File(s) | |<2> Set Application File type | |<3> Delete File | |<0> Exit To Main Menu | ============================================================================ Enter your choice(0-3): 2 'M' = MAIN 'B' = BACKUP 'S' = SECURE 'N/A' = NOT ASSIGNED ============================================================================ |NO. Size(B) Time Type Name | |No right Application file in the current device! | ============================================================================ ===============================<File CONTROL>=============================== |Note:the operating device is flash | |<1> Display All File(s) | |<2> Set Application File type | |<3> Delete File | |<0> Exit To Main Menu | ============================================================================ Enter your choice(0-3): 0 ===========================<EXTEND-BOOTWARE MENU>=========================== |<1> Boot System | |<2> Enter Serial SubMenu | |<3> Enter Ethernet SubMenu | |<4> File Control | |<5> Restore to Factory Default Configuration | |<6> Skip Current System Configuration | |<7> BootWare Operation Menu | |<8> Clear Super Password | |<9> Storage Device Operation | |<0> Reboot | ============================================================================ Ctrl+C: Display Copyright Ctrl+Y: Change AP Mode Ctrl+F: Format File System Enter your choice(0-9): 4 ===============================<File CONTROL>=============================== |Note:the operating device is flash | |<1> Display All File(s) | |<2> Set Application File type | |<3> Delete File | |<0> Exit To Main Menu | ============================================================================ Enter your choice(0-3): 0 ===========================<EXTEND-BOOTWARE MENU>=========================== |<1> Boot System | |<2> Enter Serial SubMenu | |<3> Enter Ethernet SubMenu | |<4> File Control | |<5> Restore to Factory Default Configuration | |<6> Skip Current System Configuration | |<7> BootWare Operation Menu | |<8> Clear Super Password | |<9> Storage Device Operation | |<0> Reboot | ============================================================================ Ctrl+C: Display Copyright Ctrl+Y: Change AP Mode Ctrl+F: Format File System Enter your choice(0-9): 2 ===========================<Enter Serial SubMenu>=========================== |Note:the operating device is flash | |<1> Download Application Program To SDRAM And Run | |<2> Update Main Application File | |<3> Modify Serial Interface Parameter | |<0> Exit To Main Menu | ============================================================================ Enter your choice(0-3): 1 Please Start To Transfer File, Press <Ctrl+C> To Exit. Waiting ...CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC stopped! Download failed! ===========================<Enter Serial SubMenu>=========================== |Note:the operating device is flash | |<1> Download Application Program To SDRAM And Run | |<2> Update Main Application File | |<3> Modify Serial Interface Parameter | |<0> Exit To Main Menu | ============================================================================ Enter your choice(0-3): 0 ===========================<EXTEND-BOOTWARE MENU>=========================== |<1> Boot System | |<2> Enter Serial SubMenu | |<3> Enter Ethernet SubMenu | |<4> File Control | |<5> Restore to Factory Default Configuration | |<6> Skip Current System Configuration | |<7> BootWare Operation Menu | |<8> Clear Super Password | |<9> Storage Device Operation | |<0> Reboot | ============================================================================ Ctrl+C: Display Copyright Ctrl+Y: Change AP Mode Ctrl+F: Format File System Enter your choice(0-9): 0 System is starting... Press Ctrl+D to access BASIC-BOOTWARE MENU Booting Normal Extend BootWare The Extend BootWare is self-decompressing.........................Done! **************************************************************************** * * * H3C WA4320-ACN-E BootWare, Version 1.05 * * * **************************************************************************** Copyright (c) 2004-2016 Hangzhou H3C Technologies Co., Ltd. Compiled Date : Jun 28 2016 CPU Type : ATHEROS AR9563 CPU L1 Cache : 32KB CPU Clock Speed : 775MHz Memory Type : SDRAM Memory Size : 128MB Memory Speed : 560MHz BootWare Size : 512KB Flash Size : 16MB PCB Version : Ver.B BootWare Validating... Press Ctrl+B to enter extended boot menu... Starting to get the main application file--flash:/wa4300s_fit.bin! The main application file does not exist--flash:/wa4300s_fit.bin! Starting to get the backup application file--flash:/backup.bin! The backup application file does not exist--flash:/backup.bin! Starting to get the secure application file--flash:/secure.bin! The secure application file does not exist--flash:/secure.bin! Booting App fails! Trying to get the IP address from the DHCP server...... Getting IP Address Failed, the system will reboot. [State : Idle] Reset request, rebooting the AP Rebooting...... System is starting... Press Ctrl+D to access BASIC-BOOTWARE MENU Booting Normal Extend BootWare The Extend BootWare is self-decompressing.........................Done! **************************************************************************** * * * H3C WA4320-ACN-E BootWare, Version 1.05 * * * **************************************************************************** Copyright (c) 2004-2016 Hangzhou H3C Technologies Co., Ltd. Compiled Date : Jun 28 2016 CPU Type : ATHEROS AR9563 CPU L1 Cache : 32KB CPU Clock Speed : 775MHz Memory Type : SDRAM Memory Size : 128MB Memory Speed : 560MHz BootWare Size : 512KB Flash Size : 16MB PCB Version : Ver.B BootWare Validating... Press Ctrl+B to enter extended boot menu... Starting to get the main application file--flash:/wa4300s_fit.bin! The main application file does not exist--flash:/wa4300s_fit.bin! Starting to get the backup application file--flash:/backup.bin! The backup application file does not exist--flash:/backup.bin! Starting to get the secure application file--flash:/secure.bin! The secure application file does not exist--flash:/secure.bin! Booting App fails! Trying to get the IP address from the DHCP server...... Getting IP Address Failed, the system will reboot. [State : Idle] Reset request, rebooting the AP Rebooting...... System is starting... Press Ctrl+D to access BASIC-BOOTWARE MENU Booting Normal Extend BootWare The Extend BootWare is self-decompressing.........................Done! **************************************************************************** * * * H3C WA4320-ACN-E BootWare, Version 1.05 * * * **************************************************************************** Copyright (c) 2004-2016 Hangzhou H3C Technologies Co., Ltd. Compiled Date : Jun 28 2016 CPU Type : ATHEROS AR9563 CPU L1 Cache : 32KB CPU Clock Speed : 775MHz Memory Type : SDRAM Memory Size : 128MB Memory Speed : 560MHz BootWare Size : 512KB Flash Size : 16MB PCB Version : Ver.B BootWare Validating... Press Ctrl+B to enter extended boot menu... BootWare password: Not required. Please press Enter to continue. Password recovery capability is enabled. Note: The current operating device is flash Enter < Storage Device Operation > to select device. ===========================<EXTEND-BOOTWARE MENU>=========================== |<1> Boot System | |<2> Enter Serial SubMenu | |<3> Enter Ethernet SubMenu | |<4> File Control | |<5> Restore to Factory Default Configuration | |<6> Skip Current System Configuration | |<7> BootWare Operation Menu | |<8> Clear Super Password | |<9> Storage Device Operation | |<0> Reboot | ============================================================================ Ctrl+C: Display Copyright Ctrl+Y: Change AP Mode Ctrl+F: Format File System Enter your choice(0-9): 3 ==========================<Enter Ethernet SubMenu>========================== |Note:the operating device is flash | |<1> Download Application Program To SDRAM And Run | |<2> Update Main Application File | |<3> Modify Ethernet Parameter | |<0> Exit To Main Menu | |<Ensure The Parameter Be Modified Before Downloading!> | ============================================================================ Enter your choice(0-3): 3 ==========================<ETHERNET PARAMETER SET>========================== |Note: '.' = Clear field. | | '-' = Go to previous field. | | Ctrl+D = Quit. | ============================================================================ Protocol (FTP or TFTP) :ftp tftp Load File Name :wa4300s_fat.bin :wa4300s_fat.bin Target File Name :wa4300s_fat.bin :wa4300s_fat.bin Server IP Address :192.168.0.23 192.168.0.23 Local IP Address :192.168.0.50 192.168.0.1 Gateway IP Address :0.0.0.0 0.0.0.0 ==========================<Enter Ethernet SubMenu>========================== |Note:the operating device is flash | |<1> Download Application Program To SDRAM And Run | |<2> Update Main Application File | |<3> Modify Ethernet Parameter | |<0> Exit To Main Menu | |<Ensure The Parameter Be Modified Before Downloading!> | ============================================================================ Enter your choice(0-3): 2 Loading..................................................................... ............................................................................ .......................................................................... Done! 11062272 bytes downloaded! Something wrong with the file. ==========================<Enter Ethernet SubMenu>========================== |Note:the operating device is flash | |<1> Download Application Program To SDRAM And Run | |<2> Update Main Application File | |<3> Modify Ethernet Parameter | |<0> Exit To Main Menu | |<Ensure The Parameter Be Modified Before Downloading!> | ============================================================================ Enter your choice(0-3): 0 ===========================<EXTEND-BOOTWARE MENU>=========================== |<1> Boot System | |<2> Enter Serial SubMenu | |<3> Enter Ethernet SubMenu | |<4> File Control | |<5> Restore to Factory Default Configuration | |<6> Skip Current System Configuration | |<7> BootWare Operation Menu | |<8> Clear Super Password | |<9> Storage Device Operation | |<0> Reboot | ============================================================================ Ctrl+C: Display Copyright Ctrl+Y: Change AP Mode Ctrl+F: Format File System Enter your choice(0-9): 0 System is starting... Press Ctrl+D to access BASIC-BOOTWARE MENU Booting Normal Extend BootWare The Extend BootWare is self-decompressing.........................Done! **************************************************************************** * * * H3C WA4320-ACN-E BootWare, Version 1.05 * * * **************************************************************************** Copyright (c) 2004-2016 Hangzhou H3C Technologies Co., Ltd. Compiled Date : Jun 28 2016 CPU Type : ATHEROS AR9563 CPU L1 Cache : 32KB CPU Clock Speed : 775MHz Memory Type : SDRAM Memory Size : 128MB Memory Speed : 560MHz BootWare Size : 512KB Flash Size : 16MB PCB Version : Ver.B BootWare Validating... Press Ctrl+B to enter extended boot menu... Starting to get the main application file--flash:/wa4300s_fit.bin! The main application file does not exist--flash:/wa4300s_fit.bin! Starting to get the backup application file--flash:/backup.bin! The backup application file does not exist--flash:/backup.bin! Starting to get the secure application file--flash:/secure.bin! The secure application file does not exist--flash:/secure.bin! Booting App fails! Trying to get the IP address from the DHCP server...... Getting IP Address Failed, the system will reboot. [State : Idle] Reset request, rebooting the AP Rebooting...... System is starting... Press Ctrl+D to access BASIC-BOOTWARE MENU Booting Normal Extend BootWare The Extend BootWare is self-decompressing.........................Done! **************************************************************************** * * * H3C WA4320-ACN-E BootWare, Version 1.05 * * * **************************************************************************** Copyright (c) 2004-2016 Hangzhou H3C Technologies Co., Ltd. Compiled Date : Jun 28 2016 CPU Type : ATHEROS AR9563 CPU L1 Cache : 32KB CPU Clock Speed : 775MHz Memory Type : SDRAM Memory Size : 128MB Memory Speed : 560MHz BootWare Size : 512KB Flash Size : 16MB PCB Version : Ver.B BootWare Validating... Press Ctrl+B to enter extended boot menu... Starting to get the main application file--flash:/wa4300s_fit.bin! The main application file does not exist--flash:/wa4300s_fit.bin! Starting to get the backup application file--flash:/backup.bin! The backup application file does not exist--flash:/backup.bin! Starting to get the secure application file--flash:/secure.bin! The secure application file does not exist--flash:/secure.bin! Booting App fails! Trying to get the IP address from the DHCP server......