碼上歡樂
相關內容    簡體    繁體

cisco路由的ip靜態路由添加（二）

本文轉載自   查看原文   2019-11-03 22:28   322    Cisco

 

 


路由器Corp 配置
Corp(config)#ip route 192.168.20.0 255.255.255.0 10.1.3.2 150

Corp(config)#ip route 192.168.10.0 255.255.255.0 10.1.2.2 150

Corp(config)#ip route 192.168.30.0 255.255.255.0 10.1.4.2 150

Corp(config)#ip route 192.168.40.0 255.255.255.0 10.1.4.2 150

Corp(config)#ip route 172.16.10.0 255.255.255.0 10.1.5.2 150

Corp(config)#do sh run | begin ip route

ip route 192.168.20.0 255.255.255.0 10.1.3.2 150

ip route 192.168.10.0 255.255.255.0 10.1.2.2 150

ip route 192.168.30.0 255.255.255.0 10.1.4.2 150

ip route 192.168.40.0 255.255.255.0 10.1.4.2 150

ip route 172.16.10.0 255.255.255.0 10.1.5.2 150
路由器R1配置

R1(config)#ip route 10.1.1.0 255.255.255.0 10.1.2.1 150

R1(config)#ip route 10.1.4.0 255.255.255.0 10.1.3.1 150

R1(config)#ip route 10.1.5.0 255.255.255.0 10.1.2.1 150

R1(config)#ip route 192.168.30.0 255.255.255.0 10.1.3.1 150

R1(config)#ip route 192.168.40.0 255.255.255.0 10.1.2.1 150

R1(config)#ip route 172.16.10.0 255.255.255.0 10.1.3.1 150

R1(config)#do sh run | begin ip route

ip route 10.1.1.0 255.255.255.0 10.1.2.1 150

ip route 10.1.4.0 255.255.255.0 10.1.3.1 150

ip route 10.1.5.0 255.255.255.0 10.1.2.1 150

ip route 192.168.30.0 255.255.255.0 10.1.3.1 150

ip route 192.168.40.0 255.255.255.0 10.1.2.1 150

ip route 172.16.10.0 255.255.255.0 10.1.3.1 150 

R1(config)#do sh ip rout

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

* - candidate default, U - per-user static route, o - ODR

P - periodic downloaded static route

 

Gateway of last resort is not set

 

10.0.0.0/24 is subnetted, 5 subnets

S 10.1.1.0 [150/0] via 10.1.2.1

C 10.1.2.0 is directly connected, Serial0/0/0

C 10.1.3.0 is directly connected, Serial0/0/1

S 10.1.4.0 [150/0] via 10.1.3.1

S 10.1.5.0 [150/0] via 10.1.2.1

172.16.0.0/24 is subnetted, 1 subnets

S 172.16.10.0 [150/0] via 10.1.3.1

C 192.168.10.0/24 is directly connected, FastEthernet0/0

C 192.168.20.0/24 is directly connected, FastEthernet0/1

S 192.168.30.0/24 [150/0] via 10.1.3.1

S 192.168.40.0/24 [150/0] via 10.1.2.1

 

 

 


路由器R2的配置

R2(config)#ip route 10.1.1.0 255.255.255.0 10.1.4.1 150

R2(config)#ip route 10.1.2.0 255.255.255.0 10.1.4.1 150

R2(config)#ip route 10.1.3.0 255.255.255.0 10.1.4.1 150

R2(config)#ip route 10.1.5.0 255.255.255.0 10.1.4.1 150

R2(config)#ip route 192.168.10.0 255.255.255.0 10.1.4.1 150

R2(config)#ip route 192.168.20.0 255.255.255.0 10.1.4.1 150

R2(config)#ip route 172.16.10.0 255.255.255.0 10.1.4.1 150

R2(config)#do sh run | begin ip route

ip route 10.1.1.0 255.255.255.0 10.1.4.1 150

ip route 10.1.2.0 255.255.255.0 10.1.4.1 150

ip route 10.1.3.0 255.255.255.0 10.1.4.1 150

ip route 10.1.5.0 255.255.255.0 10.1.4.1 150

ip route 192.168.10.0 255.255.255.0 10.1.4.1 150

ip route 192.168.20.0 255.255.255.0 10.1.4.1 150

ip route 172.16.10.0 255.255.255.0 10.1.4.1 150

R2(config)#do sh ip rou

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

* - candidate default, U - per-user static route, o - ODR

P - periodic downloaded static route

 

Gateway of last resort is not set

 

10.0.0.0/24 is subnetted, 5 subnets

S 10.1.1.0 [150/0] via 10.1.4.1

S 10.1.2.0 [150/0] via 10.1.4.1

S 10.1.3.0 [150/0] via 10.1.4.1

C 10.1.4.0 is directly connected, Serial0/0/0

S 10.1.5.0 [150/0] via 10.1.4.1

172.16.0.0/24 is subnetted, 1 subnets

S 172.16.10.0 [150/0] via 10.1.4.1

S 192.168.10.0/24 [150/0] via 10.1.4.1

S 192.168.20.0/24 [150/0] via 10.1.4.1

C 192.168.30.0/24 is directly connected, FastEthernet0/0

C 192.168.40.0/24 is directly connected, FastEthernet0/1

路由器R3的配置

 R3(config)#ip route 10.1.1.0 255.255.255.0 f0/0 150   

R3(config)#ip route 10.1.2.0 255.255.255.0 f0/0 150

R3(config)#ip route 10.1.3.0 255.255.255.0 f0/0 150

R3(config)#ip route 10.1.4.0 255.255.255.0 f0/0 150

R3(config)#ip route 192.168.10.0 255.255.255.0 f0/0 150

R3(config)#ip route 192.168.20.0 255.255.255.0 f0/0 150

R3(config)#ip route 192.168.30.0 255.255.255.0 f0/0 150

R3(config)#ip route 192.168.40.0 255.255.255.0 f0/0 150

R3(config)#do sh run | begin ip rout

ip route 10.1.1.0 255.255.255.0 FastEthernet0/0 150     /  * 注：此處的FastEthernet 0/0端口為R3的端口 而不是Corp路由端口/

ip route 10.1.2.0 255.255.255.0 FastEthernet0/0 150

ip route 10.1.3.0 255.255.255.0 FastEthernet0/0 150

ip route 10.1.4.0 255.255.255.0 FastEthernet0/0 150

ip route 192.168.10.0 255.255.255.0 FastEthernet0/0 150

ip route 192.168.20.0 255.255.255.0 FastEthernet0/0 150

ip route 192.168.30.0 255.255.255.0 FastEthernet0/0 150

ip route 192.168.40.0 255.255.255.0 FastEthernet0/0 150

Gateway of last resort is not set

 

10.0.0.0/24 is subnetted, 5 subnets

S 10.1.1.0 is directly connected, FastEthernet0/0

S 10.1.2.0 is directly connected, FastEthernet0/0

S 10.1.3.0 is directly connected, FastEthernet0/0

S 10.1.4.0 is directly connected, FastEthernet0/0

C 10.1.5.0 is directly connected, FastEthernet0/0

172.16.0.0/24 is subnetted, 1 subnets

C 172.16.10.0 is directly connected, Dot11Radio0/3/0

S 192.168.10.0/24 is directly connected, FastEthernet0/0

S 192.168.20.0/24 is directly connected, FastEthernet0/0

S 192.168.30.0/24 is directly connected, FastEthernet0/0

S 192.168.40.0/24 is directly connected, FastEthernet0/0
默認路由選擇  （e.g. 將R3設置為根路由）

R3(config)#no ip route 10.1.1.0 255.255.255.0

R3(config)#no ip route 10.1.2.0 255.255.255.0

R3(config)#no ip route 10.1.3.0 255.255.255.0

R3(config)#no ip route 10.1.4.0 255.255.255.0

R3(config)#no ip route 192.168.10.0 255.255.255.0

R3(config)#no ip route 192.168.20.0 255.255.255.0

R3(config)#no ip route 192.168.30.0 255.255.255.0

R3(config)#no ip route 192.168.40.0 255.255.255.0 


 R3(config)#do sh ip

sh ip

% Incomplete command.

R3(config)#do sh ip rout

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

* - candidate default, U - per-user static route, o - ODR

P - periodic downloaded static route

 

Gateway of last resort is 10.1.5.1 to network 0.0.0.0

 

10.0.0.0/24 is subnetted, 1 subnets

C 10.1.5.0 is directly connected, FastEthernet0/0

172.16.0.0/24 is subnetted, 1 subnets

C 172.16.10.0 is directly connected, Dot11Radio0/3/0

S* 0.0.0.0/0 [1/0] via 10.1.5.1

R3(config)#ip route 0.0.0.0 0.0.0.0 10.1.5.1

R3(config)#ip classless


R3(config)#do sh ip rout 

     10.0.0.0/24 is subnetted, 1 subnets

C       10.1.5.0 is directly connected, vlan 1   

     172.16.0.0/24 is subnetted, 1 subnets

C       172.16.10.0 is directly connected, Dot11Radio0/3/0

S*   0.0.0.0/0 [1/0] via 10.1.5.1  
                                 is directly connected, FastEthernet0/0   /*注：默認路由   10.1.5.1為下一跳ip   fastEthernet 0/0為R3出端口/


免責聲明！

本站轉載的文章為個人學習借鑒使用，本站對版權不負任何法律責任。如果侵犯了您的隱私權益，請聯系本站郵箱yoyou2525@163.com刪除。



猜您在找 IP路由及靜態路由配置 Cisco(思科)路由器靜態路由的配置 linux添加靜態路由 Debian如何永久添加靜態路由 Linux永久添加靜態路由 centos 添加永久靜態路由 Centos7添加靜態路由 centos 7 永久添加靜態路由 【Cisco】實現同一個路由器一個端口用動態路由，另一個端口用靜態路由 路由器中pppoe，動態IP，靜態IP的區別
 
粵ICP備18138465號   © 2018-2025 CODEPRJ.COM