先到官網https://redis.io/download下安裝包，現在最新是5.0.5版本，可惜點擊下載后被windows禁了，那就下4版本的，往下看Other versions的Old(4.0)，點4版本最新4.0.14：
redis的優點之一就是安裝包特別小，很快就能下好，點個贊。接下來進入linux的wlf用戶，通過rz上傳至soft目錄，開始執行安裝操作：
$ tar xzvf soft/redis-4.0.14.tar.gz $ cd redis-4.0.14 $ make
make構建結束后，也就安裝結束了：
LINK redis-server INSTALL redis-sentinel CC redis-cli.o LINK redis-cli CC redis-benchmark.o LINK redis-benchmark INSTALL redis-check-rdb INSTALL redis-check-aof Hint: It's a good idea to run 'make test' ;) make[1]: Leaving directory `/home/wlf/redis-4.0.14/src'
啟動redis前我們用vi改下配置文件redis.conf：
# By default, if no "bind" configuration directive is specified, Redis listens # for connections from all the network interfaces available on the server. # It is possible to listen to just one or multiple selected interfaces using # the "bind" configuration directive, followed by one or more IP addresses. # # Examples: # # bind 192.168.1.100 10.0.0.1 # bind 127.0.0.1 ::1 # # ~~~ WARNING ~~~ If the computer running Redis is directly exposed to the # internet, binding to all the interfaces is dangerous and will expose the # instance to everybody on the internet. So by default we uncomment the # following bind directive, that will force Redis to listen only into # the IPv4 lookback interface address (this means Redis will be able to # accept connections only from clients running into the same computer it # is running). # # IF YOU ARE SURE YOU WANT YOUR INSTANCE TO LISTEN TO ALL THE INTERFACES # JUST COMMENT THE FOLLOWING LINE. # ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ bind 127.0.0.1 # Protected mode is a layer of security protection, in order to avoid that # Redis instances left open on the internet are accessed and exploited. # # When protected mode is on and if: # # 1) The server is not binding explicitly to a set of addresses using the # "bind" directive. # 2) No password is configured. # # The server only accepts connections from clients connecting from the # IPv4 and IPv6 loopback addresses 127.0.0.1 and ::1, and from Unix domain # sockets. # # By default protected mode is enabled. You should disable it only if # you are sure you want clients from other hosts to connect to Redis # even if no authentication is configured, nor a specific set of interfaces # are explicitly listed using the "bind" directive. protected-mode yes
在bind 127.0.0.1前加#注掉，將protected-mode yes改為protected-mode no去掉保護策略，這樣就能支持遠程連接了。
# By default Redis does not run as a daemon. Use 'yes' if you need it. # Note that Redis will write a pid file in /var/run/redis.pid when daemonized. daemonize no # If a pid file is specified, Redis writes it where specified at startup # and removes it at exit. # # When the server runs non daemonized, no pid file is created if none is # specified in the configuration. When the server is daemonized, the pid file # is used even if not specified, defaulting to "/var/run/redis.pid". # # Creating a pid file is best effort: if Redis is not able to create it # nothing bad happens, the server will start and run normally. pidfile /var/run/redis_6379.pid
默認redis不是在后台運行的，將daemonize no改為daemonize yes，另外當后台運行時默認生成的pid文件是在/var/run目錄下，我們可以指定為自己的目錄，如改為/home/wlf/redis-4.0.14/run/redis_6379.pid
保存好后啟動redis：
$ src/redis-server redis.conf 10702:C 23 Sep 15:08:56.153 # oO0OoO0OoO0Oo Redis is starting oO0OoO0OoO0Oo 10702:C 23 Sep 15:08:56.153 # Redis version=4.0.14, bits=64, commit=00000000, modified=0, pid=10702, just started 10702:C 23 Sep 15:08:56.153 # Configuration loaded
看下進程，已經起來了：
$ netstat -nlp | grep 6379 (Not all processes could be identified, non-owned process info will not be shown, you would have to be root to see it all.) tcp 0 0 0.0.0.0:6379 0.0.0.0:* LISTEN 10703/src/redis-ser tcp6 0 0 :::6379 :::* LISTEN 10703/src/redis-ser
我們克隆會話打開另一個窗口，進入wlf用戶開啟客戶端：
$ cd redis-4.0.14/ $ src/redis-cli 127.0.0.1:6379> set wlf wumanshu OK 127.0.0.1:6379> get wlf "wumanshu"
如果我們想從客戶端遠程連接服務端，只需指定服務端ip即可，假如redis服務端ip是10.110.1.11，那么我在客戶端機器使用命令需要加參數h（默認端口也是6379）：
$ src/redis-cli -h 10.110.1.11
關閉客戶端，同時也將關閉服務端：
$ src/redis-cli shutdown $ netstat -nlp | grep 6379 (Not all processes could be identified, non-owned process info will not be shown, you would have to be root to see it all.)
或者使用telnet也可以從遠程機器連接到redis。不過因為以上設置，redis本身的安全機制已經盪然無存，此時很容被入侵，具體方法和安全防護措施參見redis支持遠程接入的安全防護問題。