CentOS7 DHCP 服務搭建

一、實驗環境

1、VMware12、倆台Linux（Ser  和  Client ）、DHCP安裝包。

二、操作流程

1、安裝DHCP

2、配置DHCP的配置文件：  /etc/dhcp/dhcpd.conf

3、測試服務

三、實操如下

1、# yum -y install dhcp*            //安裝DHCP，注意要帶上*   在Ser上操作。

2、# vim /etc/sysconfig/network-scripts/ifcfg-ens33-1           //在Ser上配置網絡IP地址，一般都是ens33

3、網絡IP設置如下：

HWADDR=00:0C:29:03:EA:35
TYPE=Ethernet
PROXY_METHOD=none
BROWSER_ONLY=no
BOOTPROTO=static                   //改為static，表示靜態地址
IPADDR=192.168.1.20                //改為和subnet 同網段的地址（此地址最好選擇range之外的地址）
PREFIX=24                                  //改為和網路IP地址對應的子網掩碼
GATEWAY=192.168.1.1              //注意：此處網關必須設置和DHCP作用域里面的網關相同
DNS1=8.8.8.8                             //DNS設置正常的就可以
DEFROUTE=yes
IPV4_FAILURE_FATAL=no
IPV6INIT=yes
IPV6_AUTOCONF=yes
IPV6_DEFROUTE=yes
IPV6_FAILURE_FATAL=no
IPV6_ADDR_GEN_MODE=stable-privacy
NAME=ens33
UUID=2d5fde3e-2e83-49af-b7d7-f326fc3a7001
ONBOOT=yes                             //保證網卡處於yes 啟動狀態

⏩按鍵esc 輸入：wq    保存退出。

#systemctl restart network         //重啟網卡  （建議重啟系統）

4、配置DHCP的配置文件： vim /etc/dhcp/dhcpd.conf

打開配置文件按照提示 #cp /usr/share/doc/dhcp*/dhcpd.conf.example /etc/dhcp/dhcpd.conf       //用示例文件覆蓋配置文件

#vim /etc/dhcp/dhcpd.conf          //正式開始編輯配置文件，加底色的保留，其他的全部dd

# dhcpd.conf
#
# Sample configuration file for ISC dhcpd
#

# option definitions common to all supported networks...
option domain-name "example.org";                                                                             //作用域名
option domain-name-servers ns1.example.org, ns2.example.org;                                //DNS

default-lease-time 600;                                                                                                  //默認租約時間
max-lease-time 7200;                                                                                                    //最大租約時間

# Use this to enble / disable dynamic dns updates globally.
#ddns-update-style none;

# If this DHCP server is the official DHCP server for the local
# network, the authoritative directive should be uncommented.
#authoritative;

# Use this to send dhcp log messages to a different log file (you also
# have to hack syslog.conf to complete the redirection).

log-facility local7;

# No service will be given on this subnet, but declaring it helps the
# DHCP server to understand the network topology.

subnet 10.152.187.0 netmask 255.255.255.0 {
}                                                                                                                       //聲明網絡拓撲

# This is a very basic subnet declaration.

subnet 10.254.239.0 netmask 255.255.255.224 {
  range 10.254.239.10 10.254.239.20;
  option routers rtr-239-0-1.example.org, rtr-239-0-2.example.org;
}

# This declaration allows BOOTP clients to get dynamic addresses,
# which we don't really recommend.

subnet 10.254.239.32 netmask 255.255.255.224 {
  range dynamic-bootp 10.254.239.40 10.254.239.60;
  option broadcast-address 10.254.239.31;

  option routers rtr-239-32-1.example.org;
}

# A slightly different configuration for an internal subnet.
subnet 10.5.5.0 netmask 255.255.255.224 {                                                 //作用域網段
  range 10.5.5.26 10.5.5.30;                                                                          //地址池范圍
  option domain-name-servers ns1.internal.example.org;                          //DNS
  option domain-name "internal.example.org";                                          //作用域名
  option routers 10.5.5.1;                                                                             //網關，Ser上面配置的網關和此網關要一致
  option broadcast-address 10.5.5.31;                                                        //廣播地址
  default-lease-time 600;                                                                            //默認租約時間
  max-lease-time 7200;                                                                              //最大租約時間
}                                                                                                                      //創建一個子網地址池

# Hosts which require special configuration options can be listed in
# host statements.   If no address is specified, the address will be
# allocated dynamically (if possible), but the host-specific information
# will still come from the host declaration.

host passacaglia {
  hardware ethernet 0:0:c0:5d:bd:95;
  filename "vmunix.passacaglia";
  server-name "toccata.fugue.com";
}

# Fixed IP addresses can also be specified for hosts.   These addresses
# should not also be listed as being available for dynamic assignment.
# Hosts for which fixed IP addresses have been specified can boot using
# BOOTP or DHCP.   Hosts for which no fixed address is specified can only
# be booted with DHCP, unless there is an address range on the subnet
# to which a BOOTP client is connected which has the dynamic-bootp flag
# set.
host fantasia {
  hardware ethernet 08:00:07:26:c0:a5;
  fixed-address fantasia.fugue.com;
}

# You can declare a class of clients and then do address allocation
# based on that.   The example below shows a case where all clients

# in a certain class get addresses on the 10.17.224/24 subnet, and all
# other clients get addresses on the 10.0.29/24 subnet.

class "foo" {
  match if substring (option vendor-class-identifier, 0, 4) = "SUNW";
}

shared-network 224-29 {
  subnet 10.17.224.0 netmask 255.255.255.0 {
    option routers rtr-224.example.org;
  }
  subnet 10.0.29.0 netmask 255.255.255.0 {
    option routers rtr-29.example.org;
  }
  pool {
    allow members of "foo";
    range 10.17.224.10 10.17.224.250;
  }
  pool {
    deny members of "foo";

range 10.0.29.10 10.0.29.230;
  }
}

⏩按鍵esc 輸入：wq    保存退出。

#systemctl start dhcpd         //啟動DHCP服務  

5、測試地址分發

首先將倆台虛擬系統Ser 和 Client 的網卡配置在同一個虛擬網絡環境中，如下圖

 

然后在Client 上 修改網卡配置文件，BOOTPROTO=dhcp   刪除靜態地址后保存 重啟網卡（也重啟電腦）

同樣在Client 上安裝DHCP服務

驗證如下：

ifconfig 查看獲取情況

route -n        //查看路由信息

也可以在Ser上執行status 命令

#systemctl status dhcpd