如何在CCS上生成.txt文件並燒錄到MSP430

本文轉載自查看原文 2018-09-11 18:50 3328

由於CCS平台程序編譯后將直接產生.out文件用於仿真器程序下載，而當在MSP430單片機開發時，可能需要用到BSL下載，此時就需要生成.txt文件用於BSL程序燒錄。

本片簡述如何在CCS上編輯單片機程序產生.txt文件並采用BSL將程序燒錄單片機。（我才用的版本為CCS8.1.0）

1，在CCS上正確創建工程文件。

新建工程：File->New->CCS Project

2，在main.c文件中編寫程序並保存。

 1 #include <msp430f169.h>
 2 /*
 3  * 軟件延時
 4  */
 5 #define CPU_F1 ((double)1000000)
 6 #define delay_us1M(x) __delay_cycles((long)(CPU_F1*(double)x/1000000.0))
 7 #define delay_ms1M(x) __delay_cycles((long)(CPU_F1*(double)x/1000.0))
 8 
 9 /**
10  * main.c
11  */
12 int main(void)
13 {
14     unsigned char j,k;
15     WDTCTL = WDTPW + WDTHOLD;//關看門狗
16     P6DIR = 0xff;//設置P4端口為輸出端口
17     while(1)
18     {
19         k = 1;
20         for(j=0;j<8;j++)//循環8次，即D1~D8輪流點亮
21         {
22             P6OUT = ~k;//反相輸出，低電平點亮LED
23             delay_ms1M(300);//延時
24             k=k<<1;//左移一位
25         }
26     }
27 
28 }

3編譯程序：Project-Build All

4,配置CCS使其產生.hex可執行文件（用Protues仿真時燒錄芯片的是.hex文件）

Project->Properties->MSP430 Hex Utility

勾選 Enable MSP430 Hex Utility 再選到Output Format Options 在Output format欄選擇Output TI-TXT hex format (--ti_txt)

7，再次編譯程序，將產生.txt文件

結果：

**** Build of configuration Debug for project LCD ****

"D:\\TI\\ccsv8\\utils\\bin\\gmake" -k -j 4 all -O

gmake[1]: 'LCD.out' is up to date.
Building files: "LCD.out"
Invoking: MSP430 Hex Utility
"D:/TI/ccsv8/tools/compiler/ti-cgt-msp430_18.1.2.LTS/bin/hex430" --memwidth=8 --romwidth=8 -o "LCD.hex" "LCD.out"
Translating to Extended Tektronix format...
"LCD.out" .text ==> .text
"LCD.out" DACDMA ==> DACDMA
"LCD.out" PORT2 ==> PORT2
"LCD.out" USART1TX ==> USART1TX
"LCD.out" USART1RX ==> USART1RX
"LCD.out" PORT1 ==> PORT1
"LCD.out" TIMERA1 ==> TIMERA1
"LCD.out" TIMERA0 ==> TIMERA0
"LCD.out" ADC12 ==> ADC12
"LCD.out" USART0TX ==> USART0TX
"LCD.out" USART0RX ==> USART0RX
"LCD.out" WDT ==> WDT
"LCD.out" COMPARATORA ==> COMPARATORA
"LCD.out" TIMERB1 ==> TIMERB1
"LCD.out" TIMERB0 ==> TIMERB0
"LCD.out" NMI ==> NMI
"LCD.out" .reset ==> .reset
Finished building: "LCD.out"

"D:/TI/ccsv8/tools/compiler/ti-cgt-msp430_18.1.2.LTS/bin/hex430" --ti_txt "LCD.out" -o "LCD.txt" -order MS -romwidth 16
Translating to TI-TXT format...
"LCD.out" .text ==> .text
"LCD.out" DACDMA ==> DACDMA
"LCD.out" PORT2 ==> PORT2
"LCD.out" USART1TX ==> USART1TX
"LCD.out" USART1RX ==> USART1RX
"LCD.out" PORT1 ==> PORT1
"LCD.out" TIMERA1 ==> TIMERA1
"LCD.out" TIMERA0 ==> TIMERA0
"LCD.out" ADC12 ==> ADC12
"LCD.out" USART0TX ==> USART0TX
"LCD.out" USART0RX ==> USART0RX
"LCD.out" WDT ==> WDT
"LCD.out" COMPARATORA ==> COMPARATORA
"LCD.out" TIMERB1 ==> TIMERB1
"LCD.out" TIMERB0 ==> TIMERB0
"LCD.out" NMI ==> NMI
"LCD.out" .reset ==> .reset