STM32-LCD-FSMC

本文转载自查看原文 2016-11-04 23:41 1398 STM32

1. TFT驱动流程

2. RGB565（共16位）格式说明

3. TFT引脚

LCD_CS：LCD片选信号
LCD_WR：LCD写信号
LCD_RD：LCD读信号
DB[17：1]：16位双向数据线
LCD_RS：命令/数据标志 (0:命令,1:数据)
LCD_RST：硬复位LCD信号
BL_CTR：背光控制信号
T_MISO/T_MOSI/T_PEN/T_CS/T_CLK，触摸屏接口信号

4. SRAM引脚

片选信号（CS）
写信号（WE，即WR）
读信号（OE，即RD）
地址线（如A0~A25）
数据线（如D0~D15）
如果SRAM支持字节控制，那么还有UB/LB信号

5. FSMC总线

6. FSMC可以把TFT当作SRAM的原因

其操作时序和SRAM的控制完全类似，唯一不同就是TFTLCD有RS信号，但是没有地址信号。

TFTLCD通过RS信号来决定传送的数据是数据还是命令，本质上可以理解为一个地址信号，比如我们把RS接在A0上面，

那么当FSMC控制器写地址0的时候，会使得A0变为0，对TFTLCD来说，就是写命令。

而FSMC写地址1的时候，A0将会变为1，对TFTLCD来说，就是写数据了。

这样，就把数据和命令区分开了，他们其实就是对应SRAM操作的两个连续地址。

当然RS也可以接在其他地址线上，战舰V3和精英板开发板都是把RS连接在A10上面，而探索者STM32F4把RS接在A6上面。

7. FSMC分为四个块，每个块256M，每个块又分为四个区，每个区64M

HADDR，是内部AHB地址总线，其中，HADDR[25:0]来自外部存储器地址FSMC_A[25:0]，而HADDR[26:27]对4个区进行寻址，如下图。

当Bank1接的是16位宽度存储器的时候：HADDR[25:1] FSMC_A[24:0]
当Bank1接的是8位宽度存储器的时候：HADDR[25:0] FSMC_A[25:0]
不论外部接8位/16位宽设备，FSMC_A[0]永远接在外部设备地址A[0]

8. 对每个区进行配置

在ST官方库提供的的寄存器定义里面，并没有定义FSMC_BCRx、FSMC_BTRx、FSMC_BWTRx等这个单独的寄存器，而是将他们进行了一些组合。规律如下：

FSMC_BCRx和FSMC_BTRx，组合成BTCR[8]寄存器组，他们的对应关系如下：

BTCR[0]对应FSMC_BCR1，BTCR[1]对应FSMC_BTR1
BTCR[2]对应FSMC_BCR2，BTCR[3]对应FSMC_BTR2
BTCR[4]对应FSMC_BCR3，BTCR[5]对应FSMC_BTR3
BTCR[6]对应FSMC_BCR4，BTCR[7]对应FSMC_BTR4

FSMC_BWTRx则组合成BWTR[7]，他们的对应关系如下：

BWTR[0]对应FSMC_BWTR1，BWTR[2]对应FSMC_BWTR2
BWTR[4]对应FSMC_BWTR3，BWTR[6]对应FSMC_BWTR4
BWTR[1]、BWTR[3]和BWTR[5]保留，没有用到。

9. 初始化TFT对应的FSMC引脚（CS，WR，RD,DB[],RS等）全部初始化为复用推挽输出

    GPIO_InitTypeDef GPIO_InitStructure;
    FSMC_NORSRAMInitTypeDef  FSMC_NORSRAMInitStructure;
    FSMC_NORSRAMTimingInitTypeDef  readWriteTiming; 
    FSMC_NORSRAMTimingInitTypeDef  writeTiming;

    RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC,ENABLE);    //使能FSMC时钟
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB|RCC_APB2Periph_GPIOD|RCC_APB2Periph_GPIOE|RCC_APB2Periph_GPIOG,ENABLE);//使能PORTB,D,E,G以及AFIO复用功能时钟

 
     GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;                 //PB0 推挽输出 背光
     GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;          //推挽输出
     GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
     GPIO_Init(GPIOB, &GPIO_InitStructure);
    
     //PORTD复用推挽输出  
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10|GPIO_Pin_14|GPIO_Pin_15;                 //    //PORTD复用推挽输出  
     GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;          //复用推挽输出   
     GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
     GPIO_Init(GPIOD, &GPIO_InitStructure); 
       
    //PORTE复用推挽输出  
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7|GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10|GPIO_Pin_11|GPIO_Pin_12|GPIO_Pin_13|GPIO_Pin_14|GPIO_Pin_15;                 //    //PORTD复用推挽输出  
     GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;          //复用推挽输出   
     GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
     GPIO_Init(GPIOE, &GPIO_InitStructure);                                                              

       //    //PORTG12复用推挽输出 A0    
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_12;     //    //PORTD复用推挽输出  
     GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;          //复用推挽输出   
     GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
     GPIO_Init(GPIOG, &GPIO_InitStructure);

10. 配置FSMC读写模式时序

    readWriteTiming.FSMC_AddressSetupTime = 0x01;     //地址建立时间（ADDSET）为2个HCLK 1/36M=27ns
    readWriteTiming.FSMC_AddressHoldTime = 0x00;     //地址保持时间（ADDHLD）模式A未用到    
    readWriteTiming.FSMC_DataSetupTime = 0x0f;         // 数据保存时间为16个HCLK,因为液晶驱动IC的读数据的时候，速度不能太快，尤其对1289这个IC。
    readWriteTiming.FSMC_BusTurnAroundDuration = 0x00;
    readWriteTiming.FSMC_CLKDivision = 0x00;
    readWriteTiming.FSMC_DataLatency = 0x00;
    readWriteTiming.FSMC_AccessMode = FSMC_AccessMode_A;     //模式A 
    

    writeTiming.FSMC_AddressSetupTime = 0x00;     //地址建立时间（ADDSET）为1个HCLK  
    writeTiming.FSMC_AddressHoldTime = 0x00;     //地址保持时间（A        
    writeTiming.FSMC_DataSetupTime = 0x03;         ////数据保存时间为4个HCLK    
    writeTiming.FSMC_BusTurnAroundDuration = 0x00;
    writeTiming.FSMC_CLKDivision = 0x00;
    writeTiming.FSMC_DataLatency = 0x00;
    writeTiming.FSMC_AccessMode = FSMC_AccessMode_A;     //模式A

11. 初始化板块1的区4

    FSMC_NORSRAMInitStructure.FSMC_Bank = FSMC_Bank1_NORSRAM4;//  这里我们使用NE4 ，也就对应BTCR[6],[7]。
    FSMC_NORSRAMInitStructure.FSMC_DataAddressMux = FSMC_DataAddressMux_Disable; // 不复用数据地址
    FSMC_NORSRAMInitStructure.FSMC_MemoryType =FSMC_MemoryType_SRAM;// FSMC_MemoryType_SRAM;  //SRAM   
    FSMC_NORSRAMInitStructure.FSMC_MemoryDataWidth = FSMC_MemoryDataWidth_16b;//存储器数据宽度为16bit   
    FSMC_NORSRAMInitStructure.FSMC_BurstAccessMode =FSMC_BurstAccessMode_Disable;// FSMC_BurstAccessMode_Disable; 
    FSMC_NORSRAMInitStructure.FSMC_WaitSignalPolarity = FSMC_WaitSignalPolarity_Low;
    FSMC_NORSRAMInitStructure.FSMC_AsynchronousWait=FSMC_AsynchronousWait_Disable; 
    FSMC_NORSRAMInitStructure.FSMC_WrapMode = FSMC_WrapMode_Disable;   
    FSMC_NORSRAMInitStructure.FSMC_WaitSignalActive = FSMC_WaitSignalActive_BeforeWaitState;  
    FSMC_NORSRAMInitStructure.FSMC_WriteOperation = FSMC_WriteOperation_Enable;    //  存储器写使能
    FSMC_NORSRAMInitStructure.FSMC_WaitSignal = FSMC_WaitSignal_Disable;   
    FSMC_NORSRAMInitStructure.FSMC_ExtendedMode = FSMC_ExtendedMode_Enable; // 读写使用不同的时序
    FSMC_NORSRAMInitStructure.FSMC_WriteBurst = FSMC_WriteBurst_Disable; 
    FSMC_NORSRAMInitStructure.FSMC_ReadWriteTimingStruct = &readWriteTiming; //读写时序
    FSMC_NORSRAMInitStructure.FSMC_WriteTimingStruct = &writeTiming;  //写时序

    FSMC_NORSRAMInit(&FSMC_NORSRAMInitStructure);  //初始化FSMC配置

    FSMC_NORSRAMCmd(FSMC_Bank1_NORSRAM4, ENABLE);  // 使能BANK1

12. 读取TFT驱动IC的ID，进行不同的初始化

delay_ms(50);                     // delay 50 ms 
      lcddev.id=LCD_ReadReg(0x0000);    //读ID（9320/9325/9328/4531/4535等IC）   
      if(lcddev.id<0XFF||lcddev.id==0XFFFF||lcddev.id==0X9300)//读到ID不正确,新增lcddev.id==0X9300判断，因为9341在未被复位的情况下会被读成9300
    {    ...

13. LCD操作结构体

我们在FSMC初始化时选择的是板块1的区域4，板块1的区域4首地址0x6C000000

我们需要写PG0引脚低电平时写命令，高电平时写数据，也就是说FSMC_A10低电平时写命令，高电平时写数据
又当Bank1接的是16位宽度存储器的时候：HADDR[25:1] FSMC_A[24:0]
也就是说HADDR[11]低电平时写命令，高电平时写数据

　　TFT发送的数据是565格式（16位），定义如下结构体
　　由结构体的特性有，后面一个元素和前面一个元素的地址相差2
　　将第11位和第0位置0，其余为为1得到一个数（7FE），该数的第11位为0（命令），将该数加2，得到新的数的第11位为1（数据）

//LCD地址结构体
typedef struct
{
    vu16 LCD_REG;
    vu16 LCD_RAM;
} LCD_TypeDef;
//使用NOR/SRAM的 Bank1.sector4,地址位HADDR[27,26]=11 A10作为数据命令区分线 
//注意设置时STM32内部会右移一位对其!                 
#define LCD_BASE        ((u32)(0x6C000000 | 0x000007FE))
#define TFTLCD          ((LCD_TypeDef *) LCD_BASE)

14. LCD参数结构体

//LCD重要参数集
typedef struct  
{                                            
    u16 width;            //LCD 宽度
    u16 height;            //LCD 高度
    u16 id;                //LCD ID
    u8  dir;            //横屏还是竖屏控制：0，竖屏；1，横屏。    
    u16    wramcmd;        //开始写gram指令
    u16  setxcmd;        //设置x坐标指令
    u16  setycmd;        //设置y坐标指令 
}_lcd_dev;       

//LCD参数
extern _lcd_dev lcddev;    //管理LCD重要参数

15. 写命令（REG），写数据（RAM），读数据（RAM）

//写寄存器函数
//regval:寄存器值
void LCD_WR_REG(u16 regval)
{   
    TFTLCD->LCD_REG=regval;//写入要写的寄存器序号     
}
//写LCD数据
//data:要写入的值
void LCD_WR_DATA(u16 data)
{     
    TFTLCD->LCD_RAM=data;         
}
//读LCD数据
//返回值:读到的值
u16 LCD_RD_DATA(void)
{
    vu16 ram;            //防止被优化
    ram=TFTLCD->LCD_RAM;    
    return ram;     
}

16. 向指定寄存器写数据，读取指定寄存器的值

void LCD_WriteReg(u16 LCD_Reg,u16 LCD_RegValue)
{    
    TFTLCD->LCD_REG = LCD_Reg;        //写入要写的寄存器序号     
    TFTLCD->LCD_RAM = LCD_RegValue;//写入数据                 
}       
//读寄存器
//LCD_Reg:寄存器地址
//返回值:读到的数据
u16 LCD_ReadReg(u16 LCD_Reg)
{                                           
    LCD_WR_REG(LCD_Reg);        //写入要读的寄存器序号
    delay_us(5);          
    return LCD_RD_DATA();        //返回读到的值
}

18. 我们需要做的就是将战舰的通用驱动代码移植，移植相关步骤：

根据硬件算出LCD结构体地址，例如

#define LCD_BASE        ((u32)(0x6C000000 | 0x000007FE))
#define TFTLCD          ((LCD_TypeDef *) LCD_BASE)

修改该初始化的相应引脚，修改背光引脚

修改相应板块区的初始化，具体是哪个区可以看LCD_CS片选连接的是FSMC哪个使能引脚。如下，分别表示第一个和第四个区

全部代码：

#ifndef __LCD_H
#define __LCD_H        
#include "sys.h"     
#include "stdlib.h"
//////////////////////////////////////////////////////////////////////////////////     
//本程序只供学习使用，未经作者许可，不得用于其它任何用途
//ALIENTEK 战舰STM32F103开发板V3
//2.4寸/2.8寸/3.5寸/4.3寸/7寸 TFT液晶驱动      
//支持驱动IC型号包括:ILI9341/ILI9325/RM68042/RM68021/ILI9320/ILI9328/LGDP4531/LGDP4535/
//                  SPFD5408/1505/B505/C505/NT35310/NT35510/SSD1963等            
//正点原子@ALIENTEK
//技术论坛:www.openedv.com
//创建日期:2010/7/4
//版本：V2.9
//版权所有，盗版必究。
//Copyright(C) 广州市星翼电子科技有限公司 2014-2024
//All rights reserved    
//********************************************************************************
//V1.2修改说明
//支持了SPFD5408的驱动,另外把液晶ID直接打印成HEX格式.方便查看LCD驱动IC.
//V1.3
//加入了快速IO的支持
//修改了背光控制的极性（适用于V1.8及以后的开发板版本）
//对于1.8版本之前(不包括1.8)的液晶模块,请修改LCD_Init函数的LCD_LED=1;为LCD_LED=1;
//V1.4
//修改了LCD_ShowChar函数，使用画点功能画字符。
//加入了横竖屏显示的支持
//V1.5 20110730
//1,修改了B505液晶读颜色有误的bug.
//2,修改了快速IO及横竖屏的设置方式.
//V1.6 20111116
//1,加入对LGDP4535液晶的驱动支持
//V1.7 20120713
//1,增加LCD_RD_DATA函数
//2,增加对ILI9341的支持
//3,增加ILI9325的独立驱动代码
//4,增加LCD_Scan_Dir函数(慎重使用)      
//6,另外修改了部分原来的函数,以适应9341的操作
//V1.8 20120905
//1,加入LCD重要参数设置结构体lcddev
//2,加入LCD_Display_Dir函数,支持在线横竖屏切换
//V1.9 20120911
//1,新增RM68042驱动（ID:6804），但是6804不支持横屏显示！！原因：改变扫描方式，
//导致6804坐标设置失效，试过很多方法都不行，暂时无解。
//V2.0 20120924
//在不硬件复位的情况下,ILI9341的ID读取会被误读成9300,修改LCD_Init,将无法识别
//的情况（读到ID为9300/非法ID）,强制指定驱动IC为ILI9341，执行9341的初始化。
//V2.1 20120930
//修正ILI9325读颜色的bug。
//V2.2 20121007
//修正LCD_Scan_Dir的bug。
//V2.3 20130120
//新增6804支持横屏显示
//V2.4 20131120
//1,新增NT35310（ID:5310）驱动器的支持
//2,新增LCD_Set_Window函数,用于设置窗口,对快速填充,比较有用,但是该函数在横屏时,不支持6804.
//V2.5 20140211
//1,新增NT35510（ID:5510）驱动器的支持
//V2.6 20140504
//1,新增ASCII 24*24字体的支持(更多字体用户可以自行添加)  
//2,修改部分函数参数,以支持MDK -O2优化
//3,针对9341/35310/35510,写时间设置为最快,尽可能的提高速度
//4,去掉了SSD1289的支持,因为1289实在是太慢了,读周期要1us...简直奇葩.不适合F4使用
//5,修正68042及C505等IC的读颜色函数的bug.
//V2.7 20140710
//1,修正LCD_Color_Fill函数的一个bug. 
//2,修正LCD_Scan_Dir函数的一个bug.
//V2.8 20140721
//1,解决MDK使用-O2优化时LCD_ReadPoint函数读点失效的问题.
//2,修正LCD_Scan_Dir横屏时设置的扫描方式显示不全的bug.
//V2.9 20141130
//1,新增对SSD1963 LCD的支持.
//2,新增LCD_SSD_BackLightSet函数
//3,取消ILI93XX的Rxx寄存器定义
//V3.0 20150423
//修改SSD1963 LCD屏的驱动参数.
//////////////////////////////////////////////////////////////////////////////////     

  
//LCD重要参数集
typedef struct  
{                                            
    u16 width;            //LCD 宽度
    u16 height;            //LCD 高度
    u16 id;                //LCD ID
    u8  dir;            //横屏还是竖屏控制：0，竖屏；1，横屏。    
    u16    wramcmd;        //开始写gram指令
    u16  setxcmd;        //设置x坐标指令
    u16  setycmd;        //设置y坐标指令 
}_lcd_dev;       

//LCD参数
extern _lcd_dev lcddev;    //管理LCD重要参数
//LCD的画笔颜色和背景色       
extern u16  POINT_COLOR;//默认红色    
extern u16  BACK_COLOR; //背景颜色.默认为白色


//////////////////////////////////////////////////////////////////////////////////     
//-----------------LCD端口定义---------------- 
#define    LCD_LED PBout(0) //LCD背光  PB0         
//LCD地址结构体
typedef struct
{
    vu16 LCD_REG;
    vu16 LCD_RAM;
} LCD_TypeDef;
//使用NOR/SRAM的 Bank1.sector4,地址位HADDR[27,26]=11 A10作为数据命令区分线 
//注意设置时STM32内部会右移一位对其!                 
#define LCD_BASE        ((u32)(0x6C000000 | 0x000007FE))
#define TFTLCD          ((LCD_TypeDef *) LCD_BASE)
//////////////////////////////////////////////////////////////////////////////////
     
//扫描方向定义
#define L2R_U2D  0 //从左到右,从上到下
#define L2R_D2U  1 //从左到右,从下到上
#define R2L_U2D  2 //从右到左,从上到下
#define R2L_D2U  3 //从右到左,从下到上

#define U2D_L2R  4 //从上到下,从左到右
#define U2D_R2L  5 //从上到下,从右到左
#define D2U_L2R  6 //从下到上,从左到右
#define D2U_R2L  7 //从下到上,从右到左     

#define DFT_SCAN_DIR  L2R_U2D  //默认的扫描方向

//画笔颜色
#define WHITE              0xFFFF
#define BLACK              0x0000      
#define BLUE              0x001F  
#define BRED             0XF81F
#define GRED              0XFFE0
#define GBLUE             0X07FF
#define RED                0xF800
#define MAGENTA            0xF81F
#define GREEN              0x07E0
#define CYAN               0x7FFF
#define YELLOW             0xFFE0
#define BROWN              0XBC40 //棕色
#define BRRED              0XFC07 //棕红色
#define GRAY               0X8430 //灰色
//GUI颜色

#define DARKBLUE           0X01CF    //深蓝色
#define LIGHTBLUE           0X7D7C    //浅蓝色  
#define GRAYBLUE            0X5458 //灰蓝色
//以上三色为PANEL的颜色 
 
#define LIGHTGREEN          0X841F //浅绿色
//#define LIGHTGRAY        0XEF5B //浅灰色(PANNEL)
#define LGRAY              0XC618 //浅灰色(PANNEL),窗体背景色

#define LGRAYBLUE        0XA651 //浅灰蓝色(中间层颜色)
#define LBBLUE           0X2B12 //浅棕蓝色(选择条目的反色)
                                                                      
void TFTLCD_Init(void);                                                           //初始化
void LCD_DisplayOn(void);                                                    //开显示
void LCD_DisplayOff(void);                                                    //关显示
void LCD_Clear(u16 Color);                                                     //清屏
void LCD_SetCursor(u16 Xpos, u16 Ypos);                                        //设置光标
void LCD_DrawPoint(u16 x,u16 y);                                            //画点
void LCD_Fast_DrawPoint(u16 x,u16 y,u16 color);                                //快速画点
u16  LCD_ReadPoint(u16 x,u16 y);                                             //读点 
void LCD_Draw_Circle(u16 x0,u16 y0,u8 r);                                     //画圆
void LCD_DrawLine(u16 x1, u16 y1, u16 x2, u16 y2);                            //画线
void LCD_DrawRectangle(u16 x1, u16 y1, u16 x2, u16 y2);                           //画矩形
void LCD_Fill(u16 sx,u16 sy,u16 ex,u16 ey,u16 color);                           //填充单色
void LCD_Color_Fill(u16 sx,u16 sy,u16 ex,u16 ey,u16 *color);                //填充指定颜色
void LCD_ShowChar(u16 x,u16 y,u8 num,u8 size,u8 mode);                        //显示一个字符
void LCD_ShowNum(u16 x,u16 y,u32 num,u8 len,u8 size);                          //显示一个数字
void LCD_ShowxNum(u16 x,u16 y,u32 num,u8 len,u8 size,u8 mode);                //显示 数字
void LCD_ShowString(u16 x,u16 y,u16 width,u16 height,u8 size,u8 *p);        //显示一个字符串,12/16字体

void LCD_WriteReg(u16 LCD_Reg, u16 LCD_RegValue);
u16 LCD_ReadReg(u16 LCD_Reg);
void LCD_WriteRAM_Prepare(void);
void LCD_WriteRAM(u16 RGB_Code);
void LCD_SSD_BackLightSet(u8 pwm);                            //SSD1963 背光控制
void LCD_Scan_Dir(u8 dir);                                    //设置屏扫描方向
void LCD_Display_Dir(u8 dir);                                //设置屏幕显示方向
void LCD_Set_Window(u16 sx,u16 sy,u16 width,u16 height);    //设置窗口                                                                                                                               
//LCD分辨率设置
#define SSD_HOR_RESOLUTION        800        //LCD水平分辨率
#define SSD_VER_RESOLUTION        480        //LCD垂直分辨率
//LCD驱动参数设置
#define SSD_HOR_PULSE_WIDTH        1        //水平脉宽
#define SSD_HOR_BACK_PORCH        210        //水平前廊
#define SSD_HOR_FRONT_PORCH        45        //水平后廊

#define SSD_VER_PULSE_WIDTH        1        //垂直脉宽
#define SSD_VER_BACK_PORCH        34        //垂直前廊
#define SSD_VER_FRONT_PORCH        10        //垂直前廊
//如下几个参数，自动计算
#define SSD_HT    (SSD_HOR_RESOLUTION+SSD_HOR_PULSE_WIDTH+SSD_HOR_BACK_PORCH+SSD_HOR_FRONT_PORCH)
#define SSD_HPS    (SSD_HOR_PULSE_WIDTH+SSD_HOR_BACK_PORCH)
#define SSD_VT     (SSD_VER_PULSE_WIDTH+SSD_VER_BACK_PORCH+SSD_VER_FRONT_PORCH+SSD_VER_RESOLUTION)
#define SSD_VPS (SSD_VER_PULSE_WIDTH+SSD_VER_BACK_PORCH)

#endif

View Code

#include "ILI93xx.h"
#include "stdlib.h"
#include "font.h" 
#include "usart.h"     
#include "delay.h"       
//////////////////////////////////////////////////////////////////////////////////     
//本程序只供学习使用，未经作者许可，不得用于其它任何用途
//ALIENTEK 战舰STM32F103开发板V3
//2.4寸/2.8寸/3.5寸/4.3寸/7寸 TFT液晶驱动      
//支持驱动IC型号包括:ILI9341/ILI9325/RM68042/RM68021/ILI9320/ILI9328/LGDP4531/LGDP4535/
//                  SPFD5408/1505/B505/C505/NT35310/NT35510/SSD1963等            
//正点原子@ALIENTEK
//技术论坛:www.openedv.com
//创建日期:2010/7/4
//版本：V2.9
//版权所有，盗版必究。
//Copyright(C) 广州市星翼电子科技有限公司 2014-2024
//All rights reserved    
//********************************************************************************
//V1.2修改说明
//支持了SPFD5408的驱动,另外把液晶ID直接打印成HEX格式.方便查看LCD驱动IC.
//V1.3
//加入了快速IO的支持
//修改了背光控制的极性（适用于V1.8及以后的开发板版本）
//对于1.8版本之前(不包括1.8)的液晶模块,请修改LCD_Init函数的LCD_LED=1;为LCD_LED=1;
//V1.4
//修改了LCD_ShowChar函数，使用画点功能画字符。
//加入了横竖屏显示的支持
//V1.5 20110730
//1,修改了B505液晶读颜色有误的bug.
//2,修改了快速IO及横竖屏的设置方式.
//V1.6 20111116
//1,加入对LGDP4535液晶的驱动支持
//V1.7 20120713
//1,增加LCD_RD_DATA函数
//2,增加对ILI9341的支持
//3,增加ILI9325的独立驱动代码
//4,增加LCD_Scan_Dir函数(慎重使用)      
//6,另外修改了部分原来的函数,以适应9341的操作
//V1.8 20120905
//1,加入LCD重要参数设置结构体lcddev
//2,加入LCD_Display_Dir函数,支持在线横竖屏切换
//V1.9 20120911
//1,新增RM68042驱动（ID:6804），但是6804不支持横屏显示！！原因：改变扫描方式，
//导致6804坐标设置失效，试过很多方法都不行，暂时无解。
//V2.0 20120924
//在不硬件复位的情况下,ILI9341的ID读取会被误读成9300,修改LCD_Init,将无法识别
//的情况（读到ID为9300/非法ID）,强制指定驱动IC为ILI9341，执行9341的初始化。
//V2.1 20120930
//修正ILI9325读颜色的bug。
//V2.2 20121007
//修正LCD_Scan_Dir的bug。
//V2.3 20130120
//新增6804支持横屏显示
//V2.4 20131120
//1,新增NT35310（ID:5310）驱动器的支持
//2,新增LCD_Set_Window函数,用于设置窗口,对快速填充,比较有用,但是该函数在横屏时,不支持6804.
//V2.5 20140211
//1,新增NT35510（ID:5510）驱动器的支持
//V2.6 20140504
//1,新增ASCII 24*24字体的支持(更多字体用户可以自行添加)  
//2,修改部分函数参数,以支持MDK -O2优化
//3,针对9341/35310/35510,写时间设置为最快,尽可能的提高速度
//4,去掉了SSD1289的支持,因为1289实在是太慢了,读周期要1us...简直奇葩.不适合F4使用
//5,修正68042及C505等IC的读颜色函数的bug.
//V2.7 20140710
//1,修正LCD_Color_Fill函数的一个bug. 
//2,修正LCD_Scan_Dir函数的一个bug.
//V2.8 20140721
//1,解决MDK使用-O2优化时LCD_ReadPoint函数读点失效的问题.
//2,修正LCD_Scan_Dir横屏时设置的扫描方式显示不全的bug.
//V2.9 20141130
//1,新增对SSD1963 LCD的支持.
//2,新增LCD_SSD_BackLightSet函数
//3,取消ILI93XX的Rxx寄存器定义
//V3.0 20150423
//修改SSD1963 LCD屏的驱动参数.
//////////////////////////////////////////////////////////////////////////////////     

//LCD的画笔颜色和背景色       
u16 POINT_COLOR=0x0000;    //画笔颜色
u16 BACK_COLOR=0xFFFF;  //背景色 
  
//管理LCD重要参数
//默认为竖屏
_lcd_dev lcddev;
     
//写寄存器函数
//regval:寄存器值
void LCD_WR_REG(u16 regval)
{   
    TFTLCD->LCD_REG=regval;//写入要写的寄存器序号     
}
//写LCD数据
//data:要写入的值
void LCD_WR_DATA(u16 data)
{     
    TFTLCD->LCD_RAM=data;         
}
//读LCD数据
//返回值:读到的值
u16 LCD_RD_DATA(void)
{
    vu16 ram;            //防止被优化
    ram=TFTLCD->LCD_RAM;    
    return ram;     
}                       
//写寄存器
//LCD_Reg:寄存器地址
//LCD_RegValue:要写入的数据
void LCD_WriteReg(u16 LCD_Reg,u16 LCD_RegValue)
{    
    TFTLCD->LCD_REG = LCD_Reg;        //写入要写的寄存器序号     
    TFTLCD->LCD_RAM = LCD_RegValue;//写入数据                 
}       
//读寄存器
//LCD_Reg:寄存器地址
//返回值:读到的数据
u16 LCD_ReadReg(u16 LCD_Reg)
{                                           
    LCD_WR_REG(LCD_Reg);        //写入要读的寄存器序号
    delay_us(5);          
    return LCD_RD_DATA();        //返回读到的值
}   
//开始写GRAM
void LCD_WriteRAM_Prepare(void)
{
     TFTLCD->LCD_REG=lcddev.wramcmd;      
}     
//LCD写GRAM
//RGB_Code:颜色值
void LCD_WriteRAM(u16 RGB_Code)
{                                
    TFTLCD->LCD_RAM = RGB_Code;//写十六位GRAM
}
//从ILI93xx读出的数据为GBR格式，而我们写入的时候为RGB格式。
//通过该函数转换
//c:GBR格式的颜色值
//返回值：RGB格式的颜色值
u16 LCD_BGR2RGB(u16 c)
{
    u16  r,g,b,rgb;   
    b=(c>>0)&0x1f;
    g=(c>>5)&0x3f;
    r=(c>>11)&0x1f;     
    rgb=(b<<11)+(g<<5)+(r<<0);         
    return(rgb);
} 
//当mdk -O1时间优化时需要设置
//延时i
void opt_delay(u8 i)
{
    while(i--);
}
//读取个某点的颜色值     
//x,y:坐标
//返回值:此点的颜色
u16 LCD_ReadPoint(u16 x,u16 y)
{
     u16 r=0,g=0,b=0;
    if(x>=lcddev.width||y>=lcddev.height)return 0;    //超过了范围,直接返回           
    LCD_SetCursor(x,y);        
    if(lcddev.id==0X9341||lcddev.id==0X6804||lcddev.id==0X5310||lcddev.id==0X1963)LCD_WR_REG(0X2E);//9341/6804/3510/1963 发送读GRAM指令
    else if(lcddev.id==0X5510)LCD_WR_REG(0X2E00);    //5510 发送读GRAM指令
    else LCD_WR_REG(0X22);                           //其他IC发送读GRAM指令
    if(lcddev.id==0X9320)opt_delay(2);                //FOR 9320,延时2us        
     r=LCD_RD_DATA();                                //dummy Read       
    if(lcddev.id==0X1963)return r;                    //1963直接读就可以 
    opt_delay(2);      
     r=LCD_RD_DATA();                                    //实际坐标颜色
     if(lcddev.id==0X9341||lcddev.id==0X5310||lcddev.id==0X5510)        //9341/NT35310/NT35510要分2次读出
     {
        opt_delay(2);      
        b=LCD_RD_DATA(); 
        g=r&0XFF;        //对于9341/5310/5510,第一次读取的是RG的值,R在前,G在后,各占8位
        g<<=8;
    } 
    if(lcddev.id==0X9325||lcddev.id==0X4535||lcddev.id==0X4531||lcddev.id==0XB505||lcddev.id==0XC505)return r;    //这几种IC直接返回颜色值
    else if(lcddev.id==0X9341||lcddev.id==0X5310||lcddev.id==0X5510)return (((r>>11)<<11)|((g>>10)<<5)|(b>>11));//ILI9341/NT35310/NT35510需要公式转换一下
    else return LCD_BGR2RGB(r);                        //其他IC
}             
//LCD开启显示
void LCD_DisplayOn(void)
{                       
    if(lcddev.id==0X9341||lcddev.id==0X6804||lcddev.id==0X5310||lcddev.id==0X1963)LCD_WR_REG(0X29);    //开启显示
    else if(lcddev.id==0X5510)LCD_WR_REG(0X2900);    //开启显示
    else LCD_WriteReg(0X07,0x0173);                      //开启显示
}     
//LCD关闭显示
void LCD_DisplayOff(void)
{       
    if(lcddev.id==0X9341||lcddev.id==0X6804||lcddev.id==0X5310||lcddev.id==0X1963)LCD_WR_REG(0X28);    //关闭显示
    else if(lcddev.id==0X5510)LCD_WR_REG(0X2800);    //关闭显示
    else LCD_WriteReg(0X07,0x0);//关闭显示 
}   
//设置光标位置
//Xpos:横坐标
//Ypos:纵坐标
void LCD_SetCursor(u16 Xpos, u16 Ypos)
{     
     if(lcddev.id==0X9341||lcddev.id==0X5310)
    {            
        LCD_WR_REG(lcddev.setxcmd); 
        LCD_WR_DATA(Xpos>>8);LCD_WR_DATA(Xpos&0XFF);              
        LCD_WR_REG(lcddev.setycmd); 
        LCD_WR_DATA(Ypos>>8);LCD_WR_DATA(Ypos&0XFF);         
    }else if(lcddev.id==0X6804)
    {
        if(lcddev.dir==1)Xpos=lcddev.width-1-Xpos;//横屏时处理
        LCD_WR_REG(lcddev.setxcmd); 
        LCD_WR_DATA(Xpos>>8);LCD_WR_DATA(Xpos&0XFF); 
        LCD_WR_REG(lcddev.setycmd); 
        LCD_WR_DATA(Ypos>>8);LCD_WR_DATA(Ypos&0XFF); 
    }else if(lcddev.id==0X1963)
    {                       
        if(lcddev.dir==0)//x坐标需要变换
        {
            Xpos=lcddev.width-1-Xpos;
            LCD_WR_REG(lcddev.setxcmd); 
            LCD_WR_DATA(0);LCD_WR_DATA(0);         
            LCD_WR_DATA(Xpos>>8);LCD_WR_DATA(Xpos&0XFF);              
        }else
        {
            LCD_WR_REG(lcddev.setxcmd); 
            LCD_WR_DATA(Xpos>>8);LCD_WR_DATA(Xpos&0XFF);         
            LCD_WR_DATA((lcddev.width-1)>>8);LCD_WR_DATA((lcddev.width-1)&0XFF);                          
        }    
        LCD_WR_REG(lcddev.setycmd); 
        LCD_WR_DATA(Ypos>>8);LCD_WR_DATA(Ypos&0XFF);         
        LCD_WR_DATA((lcddev.height-1)>>8);LCD_WR_DATA((lcddev.height-1)&0XFF);                      
        
    }else if(lcddev.id==0X5510)
    {
        LCD_WR_REG(lcddev.setxcmd);LCD_WR_DATA(Xpos>>8);         
        LCD_WR_REG(lcddev.setxcmd+1);LCD_WR_DATA(Xpos&0XFF);             
        LCD_WR_REG(lcddev.setycmd);LCD_WR_DATA(Ypos>>8);          
        LCD_WR_REG(lcddev.setycmd+1);LCD_WR_DATA(Ypos&0XFF);            
    }else
    {
        if(lcddev.dir==1)Xpos=lcddev.width-1-Xpos;//横屏其实就是调转x,y坐标
        LCD_WriteReg(lcddev.setxcmd, Xpos);
        LCD_WriteReg(lcddev.setycmd, Ypos);
    }     
}          
//设置LCD的自动扫描方向
//注意:其他函数可能会受到此函数设置的影响(尤其是9341/6804这两个奇葩),
//所以,一般设置为L2R_U2D即可,如果设置为其他扫描方式,可能导致显示不正常.
//dir:0~7,代表8个方向(具体定义见lcd.h)
//9320/9325/9328/4531/4535/1505/b505/5408/9341/5310/5510/1963等IC已经实际测试              
void LCD_Scan_Dir(u8 dir)
{
    u16 regval=0;
    u16 dirreg=0;
    u16 temp;  
    if((lcddev.dir==1&&lcddev.id!=0X6804&&lcddev.id!=0X1963)||(lcddev.dir==0&&lcddev.id==0X1963))//横屏时，对6804和1963不改变扫描方向！竖屏时1963改变方向
    {               
        switch(dir)//方向转换
        {
            case 0:dir=6;break;
            case 1:dir=7;break;
            case 2:dir=4;break;
            case 3:dir=5;break;
            case 4:dir=1;break;
            case 5:dir=0;break;
            case 6:dir=3;break;
            case 7:dir=2;break;         
        }
    } 
    if(lcddev.id==0x9341||lcddev.id==0X6804||lcddev.id==0X5310||lcddev.id==0X5510||lcddev.id==0X1963)//9341/6804/5310/5510/1963,特殊处理
    {
        switch(dir)
        {
            case L2R_U2D://从左到右,从上到下
                regval|=(0<<7)|(0<<6)|(0<<5); 
                break;
            case L2R_D2U://从左到右,从下到上
                regval|=(1<<7)|(0<<6)|(0<<5); 
                break;
            case R2L_U2D://从右到左,从上到下
                regval|=(0<<7)|(1<<6)|(0<<5); 
                break;
            case R2L_D2U://从右到左,从下到上
                regval|=(1<<7)|(1<<6)|(0<<5); 
                break;     
            case U2D_L2R://从上到下,从左到右
                regval|=(0<<7)|(0<<6)|(1<<5); 
                break;
            case U2D_R2L://从上到下,从右到左
                regval|=(0<<7)|(1<<6)|(1<<5); 
                break;
            case D2U_L2R://从下到上,从左到右
                regval|=(1<<7)|(0<<6)|(1<<5); 
                break;
            case D2U_R2L://从下到上,从右到左
                regval|=(1<<7)|(1<<6)|(1<<5); 
                break;     
        }
        if(lcddev.id==0X5510)dirreg=0X3600;
        else dirreg=0X36;
         if((lcddev.id!=0X5310)&&(lcddev.id!=0X5510)&&(lcddev.id!=0X1963))regval|=0X08;//5310/5510/1963不需要BGR   
        if(lcddev.id==0X6804)regval|=0x02;//6804的BIT6和9341的反了       
        LCD_WriteReg(dirreg,regval);
        if(lcddev.id!=0X1963)//1963不做坐标处理
        {
            if(regval&0X20)
            {
                if(lcddev.width<lcddev.height)//交换X,Y
                {
                    temp=lcddev.width;
                    lcddev.width=lcddev.height;
                    lcddev.height=temp;
                }
            }else  
            {
                if(lcddev.width>lcddev.height)//交换X,Y
                {
                    temp=lcddev.width;
                    lcddev.width=lcddev.height;
                    lcddev.height=temp;
                }
            }  
        }
        if(lcddev.id==0X5510)
        {
            LCD_WR_REG(lcddev.setxcmd);LCD_WR_DATA(0); 
            LCD_WR_REG(lcddev.setxcmd+1);LCD_WR_DATA(0); 
            LCD_WR_REG(lcddev.setxcmd+2);LCD_WR_DATA((lcddev.width-1)>>8); 
            LCD_WR_REG(lcddev.setxcmd+3);LCD_WR_DATA((lcddev.width-1)&0XFF); 
            LCD_WR_REG(lcddev.setycmd);LCD_WR_DATA(0); 
            LCD_WR_REG(lcddev.setycmd+1);LCD_WR_DATA(0); 
            LCD_WR_REG(lcddev.setycmd+2);LCD_WR_DATA((lcddev.height-1)>>8); 
            LCD_WR_REG(lcddev.setycmd+3);LCD_WR_DATA((lcddev.height-1)&0XFF);
        }else
        {
            LCD_WR_REG(lcddev.setxcmd); 
            LCD_WR_DATA(0);LCD_WR_DATA(0);
            LCD_WR_DATA((lcddev.width-1)>>8);LCD_WR_DATA((lcddev.width-1)&0XFF);
            LCD_WR_REG(lcddev.setycmd); 
            LCD_WR_DATA(0);LCD_WR_DATA(0);
            LCD_WR_DATA((lcddev.height-1)>>8);LCD_WR_DATA((lcddev.height-1)&0XFF);  
        }
      }else 
    {
        switch(dir)
        {
            case L2R_U2D://从左到右,从上到下
                regval|=(1<<5)|(1<<4)|(0<<3); 
                break;
            case L2R_D2U://从左到右,从下到上
                regval|=(0<<5)|(1<<4)|(0<<3); 
                break;
            case R2L_U2D://从右到左,从上到下
                regval|=(1<<5)|(0<<4)|(0<<3);
                break;
            case R2L_D2U://从右到左,从下到上
                regval|=(0<<5)|(0<<4)|(0<<3); 
                break;     
            case U2D_L2R://从上到下,从左到右
                regval|=(1<<5)|(1<<4)|(1<<3); 
                break;
            case U2D_R2L://从上到下,从右到左
                regval|=(1<<5)|(0<<4)|(1<<3); 
                break;
            case D2U_L2R://从下到上,从左到右
                regval|=(0<<5)|(1<<4)|(1<<3); 
                break;
            case D2U_R2L://从下到上,从右到左
                regval|=(0<<5)|(0<<4)|(1<<3); 
                break;     
        } 
        dirreg=0X03;
        regval|=1<<12; 
        LCD_WriteReg(dirreg,regval);
    }
}     
//画点
//x,y:坐标
//POINT_COLOR:此点的颜色
void LCD_DrawPoint(u16 x,u16 y)
{
    LCD_SetCursor(x,y);        //设置光标位置 
    LCD_WriteRAM_Prepare();    //开始写入GRAM
    TFTLCD->LCD_RAM=POINT_COLOR; 
}
//快速画点
//x,y:坐标
//color:颜色
void LCD_Fast_DrawPoint(u16 x,u16 y,u16 color)
{       
    if(lcddev.id==0X9341||lcddev.id==0X5310)
    {
        LCD_WR_REG(lcddev.setxcmd); 
        LCD_WR_DATA(x>>8);LCD_WR_DATA(x&0XFF);               
        LCD_WR_REG(lcddev.setycmd); 
        LCD_WR_DATA(y>>8);LCD_WR_DATA(y&0XFF);               
    }else if(lcddev.id==0X5510)
    {
        LCD_WR_REG(lcddev.setxcmd);LCD_WR_DATA(x>>8);  
        LCD_WR_REG(lcddev.setxcmd+1);LCD_WR_DATA(x&0XFF);      
        LCD_WR_REG(lcddev.setycmd);LCD_WR_DATA(y>>8);  
        LCD_WR_REG(lcddev.setycmd+1);LCD_WR_DATA(y&0XFF); 
    }else if(lcddev.id==0X1963)
    {
        if(lcddev.dir==0)x=lcddev.width-1-x;
        LCD_WR_REG(lcddev.setxcmd); 
        LCD_WR_DATA(x>>8);LCD_WR_DATA(x&0XFF);         
        LCD_WR_DATA(x>>8);LCD_WR_DATA(x&0XFF);         
        LCD_WR_REG(lcddev.setycmd); 
        LCD_WR_DATA(y>>8);LCD_WR_DATA(y&0XFF);         
        LCD_WR_DATA(y>>8);LCD_WR_DATA(y&0XFF);         
    }else if(lcddev.id==0X6804)
    {            
        if(lcddev.dir==1)x=lcddev.width-1-x;//横屏时处理
        LCD_WR_REG(lcddev.setxcmd); 
        LCD_WR_DATA(x>>8);LCD_WR_DATA(x&0XFF);             
        LCD_WR_REG(lcddev.setycmd); 
        LCD_WR_DATA(y>>8);LCD_WR_DATA(y&0XFF);         
    }else
    {
         if(lcddev.dir==1)x=lcddev.width-1-x;//横屏其实就是调转x,y坐标
        LCD_WriteReg(lcddev.setxcmd,x);
        LCD_WriteReg(lcddev.setycmd,y);
    }             
    TFTLCD->LCD_REG=lcddev.wramcmd; 
    TFTLCD->LCD_RAM=color; 
}     
//SSD1963 背光设置
//pwm:背光等级,0~100.越大越亮.
void LCD_SSD_BackLightSet(u8 pwm)
{    
    LCD_WR_REG(0xBE);    //配置PWM输出
    LCD_WR_DATA(0x05);    //1设置PWM频率
    LCD_WR_DATA(pwm*2.55);//2设置PWM占空比
    LCD_WR_DATA(0x01);    //3设置C
    LCD_WR_DATA(0xFF);    //4设置D
    LCD_WR_DATA(0x00);    //5设置E
    LCD_WR_DATA(0x00);    //6设置F
}

//设置LCD显示方向
//dir:0,竖屏；1,横屏
void LCD_Display_Dir(u8 dir)
{
    if(dir==0)            //竖屏
    {
        lcddev.dir=0;    //竖屏
        lcddev.width=240;
        lcddev.height=320;
        if(lcddev.id==0X9341||lcddev.id==0X6804||lcddev.id==0X5310)
        {
            lcddev.wramcmd=0X2C;
             lcddev.setxcmd=0X2A;
            lcddev.setycmd=0X2B;       
            if(lcddev.id==0X6804||lcddev.id==0X5310)
            {
                lcddev.width=320;
                lcddev.height=480;
            }
        }else if(lcddev.id==0x5510)
        {
            lcddev.wramcmd=0X2C00;
             lcddev.setxcmd=0X2A00;
            lcddev.setycmd=0X2B00; 
            lcddev.width=480;
            lcddev.height=800;
        }else if(lcddev.id==0X1963)
        {
            lcddev.wramcmd=0X2C;    //设置写入GRAM的指令 
            lcddev.setxcmd=0X2B;    //设置写X坐标指令
            lcddev.setycmd=0X2A;    //设置写Y坐标指令
            lcddev.width=480;        //设置宽度480
            lcddev.height=800;        //设置高度800  
        }else
        {
            lcddev.wramcmd=0X22;
             lcddev.setxcmd=0X20;
            lcddev.setycmd=0X21;  
        }
    }else                 //横屏
    {                      
        lcddev.dir=1;    //横屏
        lcddev.width=320;
        lcddev.height=240;
        if(lcddev.id==0X9341||lcddev.id==0X5310)
        {
            lcddev.wramcmd=0X2C;
             lcddev.setxcmd=0X2A;
            lcddev.setycmd=0X2B;       
        }else if(lcddev.id==0X6804)     
        {
             lcddev.wramcmd=0X2C;
             lcddev.setxcmd=0X2B;
            lcddev.setycmd=0X2A; 
        }else if(lcddev.id==0x5510)
        {
            lcddev.wramcmd=0X2C00;
             lcddev.setxcmd=0X2A00;
            lcddev.setycmd=0X2B00; 
            lcddev.width=800;
            lcddev.height=480;
        }else if(lcddev.id==0X1963)
        {
            lcddev.wramcmd=0X2C;    //设置写入GRAM的指令 
            lcddev.setxcmd=0X2A;    //设置写X坐标指令
            lcddev.setycmd=0X2B;    //设置写Y坐标指令
            lcddev.width=800;        //设置宽度800
            lcddev.height=480;        //设置高度480  
        }else
        {
            lcddev.wramcmd=0X22;
             lcddev.setxcmd=0X21;
            lcddev.setycmd=0X20;  
        }
        if(lcddev.id==0X6804||lcddev.id==0X5310)
        {      
            lcddev.width=480;
            lcddev.height=320;             
        }
    } 
    LCD_Scan_Dir(DFT_SCAN_DIR);    //默认扫描方向
}     
//设置窗口,并自动设置画点坐标到窗口左上角(sx,sy).
//sx,sy:窗口起始坐标(左上角)
//width,height:窗口宽度和高度,必须大于0!!
//窗体大小:width*height. 
void LCD_Set_Window(u16 sx,u16 sy,u16 width,u16 height)
{    
    u8 hsareg,heareg,vsareg,veareg;
    u16 hsaval,heaval,vsaval,veaval; 
    u16 twidth,theight;
    twidth=sx+width-1;
    theight=sy+height-1;
    if(lcddev.id==0X9341||lcddev.id==0X5310||lcddev.id==0X6804||(lcddev.dir==1&&lcddev.id==0X1963))
    {
        LCD_WR_REG(lcddev.setxcmd); 
        LCD_WR_DATA(sx>>8); 
        LCD_WR_DATA(sx&0XFF);     
        LCD_WR_DATA(twidth>>8); 
        LCD_WR_DATA(twidth&0XFF);  
        LCD_WR_REG(lcddev.setycmd); 
        LCD_WR_DATA(sy>>8); 
        LCD_WR_DATA(sy&0XFF); 
        LCD_WR_DATA(theight>>8); 
        LCD_WR_DATA(theight&0XFF); 
    }else if(lcddev.id==0X1963)//1963竖屏特殊处理
    {
        sx=lcddev.width-width-sx; 
        height=sy+height-1; 
        LCD_WR_REG(lcddev.setxcmd); 
        LCD_WR_DATA(sx>>8); 
        LCD_WR_DATA(sx&0XFF);     
        LCD_WR_DATA((sx+width-1)>>8); 
        LCD_WR_DATA((sx+width-1)&0XFF);  
        LCD_WR_REG(lcddev.setycmd); 
        LCD_WR_DATA(sy>>8); 
        LCD_WR_DATA(sy&0XFF); 
        LCD_WR_DATA(height>>8); 
        LCD_WR_DATA(height&0XFF);         
    }else if(lcddev.id==0X5510)
    {
        LCD_WR_REG(lcddev.setxcmd);LCD_WR_DATA(sx>>8);  
        LCD_WR_REG(lcddev.setxcmd+1);LCD_WR_DATA(sx&0XFF);      
        LCD_WR_REG(lcddev.setxcmd+2);LCD_WR_DATA(twidth>>8);   
        LCD_WR_REG(lcddev.setxcmd+3);LCD_WR_DATA(twidth&0XFF);   
        LCD_WR_REG(lcddev.setycmd);LCD_WR_DATA(sy>>8);   
        LCD_WR_REG(lcddev.setycmd+1);LCD_WR_DATA(sy&0XFF);  
        LCD_WR_REG(lcddev.setycmd+2);LCD_WR_DATA(theight>>8);   
        LCD_WR_REG(lcddev.setycmd+3);LCD_WR_DATA(theight&0XFF);  
    }else    //其他驱动IC
    {
        if(lcddev.dir==1)//横屏
        {
            //窗口值
            hsaval=sy;                
            heaval=theight;
            vsaval=lcddev.width-twidth-1;
            veaval=lcddev.width-sx-1;                
        }else
        { 
            hsaval=sx;                
            heaval=twidth;
            vsaval=sy;
            veaval=theight;
        } 
        hsareg=0X50;heareg=0X51;//水平方向窗口寄存器
        vsareg=0X52;veareg=0X53;//垂直方向窗口寄存器                                     
        //设置寄存器值
        LCD_WriteReg(hsareg,hsaval);
        LCD_WriteReg(heareg,heaval);
        LCD_WriteReg(vsareg,vsaval);
        LCD_WriteReg(veareg,veaval);        
        LCD_SetCursor(sx,sy);    //设置光标位置
    }
}
//初始化lcd
//该初始化函数可以初始化各种ILI93XX液晶,但是其他函数是基于ILI9320的!!!
//在其他型号的驱动芯片上没有测试! 
void TFTLCD_Init(void)
{                     
    GPIO_InitTypeDef GPIO_InitStructure;
    FSMC_NORSRAMInitTypeDef  FSMC_NORSRAMInitStructure;
    FSMC_NORSRAMTimingInitTypeDef  readWriteTiming; 
    FSMC_NORSRAMTimingInitTypeDef  writeTiming;

    RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC,ENABLE);    //使能FSMC时钟
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB|RCC_APB2Periph_GPIOD|RCC_APB2Periph_GPIOE|RCC_APB2Periph_GPIOG,ENABLE);//使能PORTB,D,E,G以及AFIO复用功能时钟

 
     GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;                 //PB0 推挽输出 背光
     GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;          //推挽输出
     GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
     GPIO_Init(GPIOB, &GPIO_InitStructure);
    
     //PORTD复用推挽输出  
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10|GPIO_Pin_14|GPIO_Pin_15;                 //    //PORTD复用推挽输出  
     GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;          //复用推挽输出   
     GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
     GPIO_Init(GPIOD, &GPIO_InitStructure); 
       
    //PORTE复用推挽输出  
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7|GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10|GPIO_Pin_11|GPIO_Pin_12|GPIO_Pin_13|GPIO_Pin_14|GPIO_Pin_15;                 //    //PORTD复用推挽输出  
     GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;          //复用推挽输出   
     GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
     GPIO_Init(GPIOE, &GPIO_InitStructure);                                                              

       //    //PORTG12复用推挽输出 A0    
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_12;     //    //PORTD复用推挽输出  
     GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;          //复用推挽输出   
     GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
     GPIO_Init(GPIOG, &GPIO_InitStructure); 

    readWriteTiming.FSMC_AddressSetupTime = 0x01;     //地址建立时间（ADDSET）为2个HCLK 1/36M=27ns
    readWriteTiming.FSMC_AddressHoldTime = 0x00;     //地址保持时间（ADDHLD）模式A未用到    
    readWriteTiming.FSMC_DataSetupTime = 0x0f;         // 数据保存时间为16个HCLK,因为液晶驱动IC的读数据的时候，速度不能太快，尤其对1289这个IC。
    readWriteTiming.FSMC_BusTurnAroundDuration = 0x00;
    readWriteTiming.FSMC_CLKDivision = 0x00;
    readWriteTiming.FSMC_DataLatency = 0x00;
    readWriteTiming.FSMC_AccessMode = FSMC_AccessMode_A;     //模式A 
    

    writeTiming.FSMC_AddressSetupTime = 0x00;     //地址建立时间（ADDSET）为1个HCLK  
    writeTiming.FSMC_AddressHoldTime = 0x00;     //地址保持时间（A        
    writeTiming.FSMC_DataSetupTime = 0x03;         ////数据保存时间为4个HCLK    
    writeTiming.FSMC_BusTurnAroundDuration = 0x00;
    writeTiming.FSMC_CLKDivision = 0x00;
    writeTiming.FSMC_DataLatency = 0x00;
    writeTiming.FSMC_AccessMode = FSMC_AccessMode_A;     //模式A 

 
    FSMC_NORSRAMInitStructure.FSMC_Bank = FSMC_Bank1_NORSRAM4;//  这里我们使用NE4 ，也就对应BTCR[6],[7]。
    FSMC_NORSRAMInitStructure.FSMC_DataAddressMux = FSMC_DataAddressMux_Disable; // 不复用数据地址
    FSMC_NORSRAMInitStructure.FSMC_MemoryType =FSMC_MemoryType_SRAM;// FSMC_MemoryType_SRAM;  //SRAM   
    FSMC_NORSRAMInitStructure.FSMC_MemoryDataWidth = FSMC_MemoryDataWidth_16b;//存储器数据宽度为16bit   
    FSMC_NORSRAMInitStructure.FSMC_BurstAccessMode =FSMC_BurstAccessMode_Disable;// FSMC_BurstAccessMode_Disable; 
    FSMC_NORSRAMInitStructure.FSMC_WaitSignalPolarity = FSMC_WaitSignalPolarity_Low;
    FSMC_NORSRAMInitStructure.FSMC_AsynchronousWait=FSMC_AsynchronousWait_Disable; 
    FSMC_NORSRAMInitStructure.FSMC_WrapMode = FSMC_WrapMode_Disable;   
    FSMC_NORSRAMInitStructure.FSMC_WaitSignalActive = FSMC_WaitSignalActive_BeforeWaitState;  
    FSMC_NORSRAMInitStructure.FSMC_WriteOperation = FSMC_WriteOperation_Enable;    //  存储器写使能
    FSMC_NORSRAMInitStructure.FSMC_WaitSignal = FSMC_WaitSignal_Disable;   
    FSMC_NORSRAMInitStructure.FSMC_ExtendedMode = FSMC_ExtendedMode_Enable; // 读写使用不同的时序
    FSMC_NORSRAMInitStructure.FSMC_WriteBurst = FSMC_WriteBurst_Disable; 
    FSMC_NORSRAMInitStructure.FSMC_ReadWriteTimingStruct = &readWriteTiming; //读写时序
    FSMC_NORSRAMInitStructure.FSMC_WriteTimingStruct = &writeTiming;  //写时序

    FSMC_NORSRAMInit(&FSMC_NORSRAMInitStructure);  //初始化FSMC配置

    FSMC_NORSRAMCmd(FSMC_Bank1_NORSRAM4, ENABLE);  // 使能BANK1 
        
 
    delay_ms(50);                     // delay 50 ms 
      lcddev.id=LCD_ReadReg(0x0000);    //读ID（9320/9325/9328/4531/4535等IC）   
      if(lcddev.id<0XFF||lcddev.id==0XFFFF||lcddev.id==0X9300)//读到ID不正确,新增lcddev.id==0X9300判断，因为9341在未被复位的情况下会被读成9300
    {    
         //尝试9341 ID的读取        
        LCD_WR_REG(0XD3);                   
        lcddev.id=LCD_RD_DATA();    //dummy read     
         lcddev.id=LCD_RD_DATA();    //读到0X00
          lcddev.id=LCD_RD_DATA();       //读取93                                   
         lcddev.id<<=8;
        lcddev.id|=LCD_RD_DATA();      //读取41                       
         if(lcddev.id!=0X9341)        //非9341,尝试是不是6804
        {    
             LCD_WR_REG(0XBF);                   
            lcddev.id=LCD_RD_DATA();     //dummy read      
             lcddev.id=LCD_RD_DATA();       //读回0X01               
             lcddev.id=LCD_RD_DATA();     //读回0XD0                   
              lcddev.id=LCD_RD_DATA();    //这里读回0X68 
            lcddev.id<<=8;
              lcddev.id|=LCD_RD_DATA();    //这里读回0X04      
            if(lcddev.id!=0X6804)        //也不是6804,尝试看看是不是NT35310
            { 
                LCD_WR_REG(0XD4);                   
                lcddev.id=LCD_RD_DATA();//dummy read  
                lcddev.id=LCD_RD_DATA();//读回0X01     
                lcddev.id=LCD_RD_DATA();//读回0X53    
                lcddev.id<<=8;     
                lcddev.id|=LCD_RD_DATA();    //这里读回0X10     
                if(lcddev.id!=0X5310)        //也不是NT35310,尝试看看是不是NT35510
                {
                    LCD_WR_REG(0XDA00);    
                    lcddev.id=LCD_RD_DATA();        //读回0X00     
                    LCD_WR_REG(0XDB00);    
                    lcddev.id=LCD_RD_DATA();        //读回0X80
                    lcddev.id<<=8;    
                    LCD_WR_REG(0XDC00);    
                    lcddev.id|=LCD_RD_DATA();        //读回0X00        
                    if(lcddev.id==0x8000)lcddev.id=0x5510;//NT35510读回的ID是8000H,为方便区分,我们强制设置为5510
                    if(lcddev.id!=0X5510)            //也不是NT5510,尝试看看是不是SSD1963
                    {
                        LCD_WR_REG(0XA1);
                        lcddev.id=LCD_RD_DATA();
                        lcddev.id=LCD_RD_DATA();    //读回0X57
                        lcddev.id<<=8;     
                        lcddev.id|=LCD_RD_DATA();    //读回0X61    
                        if(lcddev.id==0X5761)lcddev.id=0X1963;//SSD1963读回的ID是5761H,为方便区分,我们强制设置为1963
                    }
                }
            }
         }      
    } 
     printf(" LCD ID:%x\r\n",lcddev.id); //打印LCD ID   
    if(lcddev.id==0X9341)    //9341初始化
    {     
        LCD_WR_REG(0xCF);  
        LCD_WR_DATA(0x00); 
        LCD_WR_DATA(0xC1); 
        LCD_WR_DATA(0X30); 
        LCD_WR_REG(0xED);  
        LCD_WR_DATA(0x64); 
        LCD_WR_DATA(0x03); 
        LCD_WR_DATA(0X12); 
        LCD_WR_DATA(0X81); 
        LCD_WR_REG(0xE8);  
        LCD_WR_DATA(0x85); 
        LCD_WR_DATA(0x10); 
        LCD_WR_DATA(0x7A); 
        LCD_WR_REG(0xCB);  
        LCD_WR_DATA(0x39); 
        LCD_WR_DATA(0x2C); 
        LCD_WR_DATA(0x00); 
        LCD_WR_DATA(0x34); 
        LCD_WR_DATA(0x02); 
        LCD_WR_REG(0xF7);  
        LCD_WR_DATA(0x20); 
        LCD_WR_REG(0xEA);  
        LCD_WR_DATA(0x00); 
        LCD_WR_DATA(0x00); 
        LCD_WR_REG(0xC0);    //Power control 
        LCD_WR_DATA(0x1B);   //VRH[5:0] 
        LCD_WR_REG(0xC1);    //Power control 
        LCD_WR_DATA(0x01);   //SAP[2:0];BT[3:0] 
        LCD_WR_REG(0xC5);    //VCM control 
        LCD_WR_DATA(0x30);      //3F
        LCD_WR_DATA(0x30);      //3C
        LCD_WR_REG(0xC7);    //VCM control2 
        LCD_WR_DATA(0XB7); 
        LCD_WR_REG(0x36);    // Memory Access Control 
        LCD_WR_DATA(0x48); 
        LCD_WR_REG(0x3A);   
        LCD_WR_DATA(0x55); 
        LCD_WR_REG(0xB1);   
        LCD_WR_DATA(0x00);   
        LCD_WR_DATA(0x1A); 
        LCD_WR_REG(0xB6);    // Display Function Control 
        LCD_WR_DATA(0x0A); 
        LCD_WR_DATA(0xA2); 
        LCD_WR_REG(0xF2);    // 3Gamma Function Disable 
        LCD_WR_DATA(0x00); 
        LCD_WR_REG(0x26);    //Gamma curve selected 
        LCD_WR_DATA(0x01); 
        LCD_WR_REG(0xE0);    //Set Gamma 
        LCD_WR_DATA(0x0F); 
        LCD_WR_DATA(0x2A); 
        LCD_WR_DATA(0x28); 
        LCD_WR_DATA(0x08); 
        LCD_WR_DATA(0x0E); 
        LCD_WR_DATA(0x08); 
        LCD_WR_DATA(0x54); 
        LCD_WR_DATA(0XA9); 
        LCD_WR_DATA(0x43); 
        LCD_WR_DATA(0x0A); 
        LCD_WR_DATA(0x0F); 
        LCD_WR_DATA(0x00); 
        LCD_WR_DATA(0x00); 
        LCD_WR_DATA(0x00); 
        LCD_WR_DATA(0x00);          
        LCD_WR_REG(0XE1);    //Set Gamma 
        LCD_WR_DATA(0x00); 
        LCD_WR_DATA(0x15); 
        LCD_WR_DATA(0x17); 
        LCD_WR_DATA(0x07); 
        LCD_WR_DATA(0x11); 
        LCD_WR_DATA(0x06); 
        LCD_WR_DATA(0x2B); 
        LCD_WR_DATA(0x56); 
        LCD_WR_DATA(0x3C); 
        LCD_WR_DATA(0x05); 
        LCD_WR_DATA(0x10); 
        LCD_WR_DATA(0x0F); 
        LCD_WR_DATA(0x3F); 
        LCD_WR_DATA(0x3F); 
        LCD_WR_DATA(0x0F); 
        LCD_WR_REG(0x2B); 
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x01);
        LCD_WR_DATA(0x3f);
        LCD_WR_REG(0x2A); 
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xef);     
        LCD_WR_REG(0x11); //Exit Sleep
        delay_ms(120);
        LCD_WR_REG(0x29); //display on    
    }else if(lcddev.id==0x6804) //6804初始化
    {
        LCD_WR_REG(0X11);
        delay_ms(20);
        LCD_WR_REG(0XD0);//VCI1  VCL  VGH  VGL DDVDH VREG1OUT power amplitude setting
        LCD_WR_DATA(0X07); 
        LCD_WR_DATA(0X42); 
        LCD_WR_DATA(0X1D); 
        LCD_WR_REG(0XD1);//VCOMH VCOM_AC amplitude setting
        LCD_WR_DATA(0X00);
        LCD_WR_DATA(0X1a);
        LCD_WR_DATA(0X09); 
        LCD_WR_REG(0XD2);//Operational Amplifier Circuit Constant Current Adjust , charge pump frequency setting
        LCD_WR_DATA(0X01);
        LCD_WR_DATA(0X22);
        LCD_WR_REG(0XC0);//REV SM GS 
        LCD_WR_DATA(0X10);
        LCD_WR_DATA(0X3B);
        LCD_WR_DATA(0X00);
        LCD_WR_DATA(0X02);
        LCD_WR_DATA(0X11);
        
        LCD_WR_REG(0XC5);// Frame rate setting = 72HZ  when setting 0x03
        LCD_WR_DATA(0X03);
        
        LCD_WR_REG(0XC8);//Gamma setting
        LCD_WR_DATA(0X00);
        LCD_WR_DATA(0X25);
        LCD_WR_DATA(0X21);
        LCD_WR_DATA(0X05);
        LCD_WR_DATA(0X00);
        LCD_WR_DATA(0X0a);
        LCD_WR_DATA(0X65);
        LCD_WR_DATA(0X25);
        LCD_WR_DATA(0X77);
        LCD_WR_DATA(0X50);
        LCD_WR_DATA(0X0f);
        LCD_WR_DATA(0X00);      
                          
           LCD_WR_REG(0XF8);
        LCD_WR_DATA(0X01);      

         LCD_WR_REG(0XFE);
         LCD_WR_DATA(0X00);
         LCD_WR_DATA(0X02);
        
        LCD_WR_REG(0X20);//Exit invert mode

        LCD_WR_REG(0X36);
        LCD_WR_DATA(0X08);//原来是a
        
        LCD_WR_REG(0X3A);
        LCD_WR_DATA(0X55);//16位模式      
        LCD_WR_REG(0X2B);
        LCD_WR_DATA(0X00);
        LCD_WR_DATA(0X00);
        LCD_WR_DATA(0X01);
        LCD_WR_DATA(0X3F);
        
        LCD_WR_REG(0X2A);
        LCD_WR_DATA(0X00);
        LCD_WR_DATA(0X00);
        LCD_WR_DATA(0X01);
        LCD_WR_DATA(0XDF);
        delay_ms(120);
        LCD_WR_REG(0X29);      
     }else if(lcddev.id==0x5310)
    { 
        LCD_WR_REG(0xED);
        LCD_WR_DATA(0x01);
        LCD_WR_DATA(0xFE);

        LCD_WR_REG(0xEE);
        LCD_WR_DATA(0xDE);
        LCD_WR_DATA(0x21);

        LCD_WR_REG(0xF1);
        LCD_WR_DATA(0x01);
        LCD_WR_REG(0xDF);
        LCD_WR_DATA(0x10);

        //VCOMvoltage//
        LCD_WR_REG(0xC4);
        LCD_WR_DATA(0x8F);      //5f

        LCD_WR_REG(0xC6);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xE2);
        LCD_WR_DATA(0xE2);
        LCD_WR_DATA(0xE2);
        LCD_WR_REG(0xBF);
        LCD_WR_DATA(0xAA);

        LCD_WR_REG(0xB0);
        LCD_WR_DATA(0x0D);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x0D);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x11);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x19);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x21);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x2D);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x3D);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x5D);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x5D);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xB1);
        LCD_WR_DATA(0x80);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x8B);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x96);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xB2);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x02);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x03);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xB3);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xB4);
        LCD_WR_DATA(0x8B);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x96);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xA1);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xB5);
        LCD_WR_DATA(0x02);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x03);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x04);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xB6);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xB7);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x3F);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x5E);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x64);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x8C);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xAC);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xDC);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x70);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x90);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xEB);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xDC);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xB8);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xBA);
        LCD_WR_DATA(0x24);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xC1);
        LCD_WR_DATA(0x20);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x54);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xFF);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xC2);
        LCD_WR_DATA(0x0A);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x04);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xC3);
        LCD_WR_DATA(0x3C);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x3A);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x39);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x37);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x3C);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x36);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x32);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x2F);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x2C);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x29);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x26);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x24);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x24);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x23);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x3C);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x36);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x32);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x2F);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x2C);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x29);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x26);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x24);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x24);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x23);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xC4);
        LCD_WR_DATA(0x62);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x05);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x84);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xF0);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x18);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xA4);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x18);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x50);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x0C);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x17);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x95);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xF3);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xE6);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xC5);
        LCD_WR_DATA(0x32);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x44);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x65);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x76);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x88);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xC6);
        LCD_WR_DATA(0x20);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x17);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x01);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xC7);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xC8);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xC9);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xE0);
        LCD_WR_DATA(0x16);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x1C);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x21);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x36);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x46);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x52);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x64);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x7A);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x8B);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x99);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xA8);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xB9);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xC4);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xCA);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xD2);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xD9);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xE0);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xF3);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xE1);
        LCD_WR_DATA(0x16);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x1C);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x22);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x36);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x45);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x52);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x64);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x7A);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x8B);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x99);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xA8);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xB9);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xC4);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xCA);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xD2);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xD8);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xE0);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xF3);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xE2);
        LCD_WR_DATA(0x05);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x0B);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x1B);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x34);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x44);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x4F);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x61);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x79);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x88);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x97);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xA6);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xB7);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xC2);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xC7);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xD1);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xD6);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xDD);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xF3);
        LCD_WR_DATA(0x00);
        LCD_WR_REG(0xE3);
        LCD_WR_DATA(0x05);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xA);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x1C);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x33);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x44);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x50);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x62);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x78);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x88);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x97);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xA6);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xB7);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xC2);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xC7);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xD1);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xD5);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xDD);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xF3);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xE4);
        LCD_WR_DATA(0x01);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x01);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x02);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x2A);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x3C);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x4B);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x5D);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x74);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x84);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x93);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xA2);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xB3);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xBE);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xC4);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xCD);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xD3);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xDD);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xF3);
        LCD_WR_DATA(0x00);
        LCD_WR_REG(0xE5);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x02);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x29);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x3C);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x4B);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x5D);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x74);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x84);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x93);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xA2);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xB3);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xBE);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xC4);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xCD);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xD3);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xDC);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xF3);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xE6);
        LCD_WR_DATA(0x11);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x34);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x56);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x76);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x77);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x66);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x88);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x99);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xBB);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x99);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x66);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x55);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x55);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x45);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x43);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x44);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xE7);
        LCD_WR_DATA(0x32);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x55);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x76);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x66);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x67);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x67);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x87);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x99);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xBB);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x99);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x77);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x44);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x56);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x23); 
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x33);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x45);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xE8);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x99);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x87);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x88);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x77);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x66);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x88);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xAA);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0xBB);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x99);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x66);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x55);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x55);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x44);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x44);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x55);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xE9);
        LCD_WR_DATA(0xAA);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0x00);
        LCD_WR_DATA(0xAA);

        LCD_WR_REG(0xCF);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xF0);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x50);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xF3);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0xF9);
        LCD_WR_DATA(0x06);
        LCD_WR_DATA(0x10);
        LCD_WR_DATA(0x29);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0x3A);
        LCD_WR_DATA(0x55);    //66

        LCD_WR_REG(0x11);
        delay_ms(100);
        LCD_WR_REG(0x29);
        LCD_WR_REG(0x35);
        LCD_WR_DATA(0x00);

        LCD_WR_REG(0x51);
        LCD_WR_DATA(0xFF);
        LCD_WR_REG(0x53);
        LCD_WR_DATA(0x2C);
        LCD_WR_REG(0x55);
        LCD_WR_DATA(0x82);
        LCD_WR_REG(0x2c);
    }else if(lcddev.id==0x5510)
    {
        LCD_WriteReg(0xF000,0x55);
        LCD_WriteReg(0xF001,0xAA);
        LCD_WriteReg(0xF002,0x52);
        LCD_WriteReg(0xF003,0x08);
        LCD_WriteReg(0xF004,0x01);
        //AVDD Set AVDD 5.2V
        LCD_WriteReg(0xB000,0x0D);
        LCD_WriteReg(0xB001,0x0D);
        LCD_WriteReg(0xB002,0x0D);
        //AVDD ratio
        LCD_WriteReg(0xB600,0x34);
        LCD_WriteReg(0xB601,0x34);
        LCD_WriteReg(0xB602,0x34);
        //AVEE -5.2V
        LCD_WriteReg(0xB100,0x0D);
        LCD_WriteReg(0xB101,0x0D);
        LCD_WriteReg(0xB102,0x0D);
        //AVEE ratio
        LCD_WriteReg(0xB700,0x34);
        LCD_WriteReg(0xB701,0x34);
        LCD_WriteReg(0xB702,0x34);
        //VCL -2.5V
        LCD_WriteReg(0xB200,0x00);
        LCD_WriteReg(0xB201,0x00);
        LCD_WriteReg(0xB202,0x00);
        //VCL ratio
        LCD_WriteReg(0xB800,0x24);
        LCD_WriteReg(0xB801,0x24);
        LCD_WriteReg(0xB802,0x24);
        //VGH 15V (Free pump)
        LCD_WriteReg(0xBF00,0x01);
        LCD_WriteReg(0xB300,0x0F);
        LCD_WriteReg(0xB301,0x0F);
        LCD_WriteReg(0xB302,0x0F);
        //VGH ratio
        LCD_WriteReg(0xB900,0x34);
        LCD_WriteReg(0xB901,0x34);
        LCD_WriteReg(0xB902,0x34);
        //VGL_REG -10V
        LCD_WriteReg(0xB500,0x08);
        LCD_WriteReg(0xB501,0x08);
        LCD_WriteReg(0xB502,0x08);
        LCD_WriteReg(0xC200,0x03);
        //VGLX ratio
        LCD_WriteReg(0xBA00,0x24);
        LCD_WriteReg(0xBA01,0x24);
        LCD_WriteReg(0xBA02,0x24);
        //VGMP/VGSP 4.5V/0V
        LCD_WriteReg(0xBC00,0x00);
        LCD_WriteReg(0xBC01,0x78);
        LCD_WriteReg(0xBC02,0x00);
        //VGMN/VGSN -4.5V/0V
        LCD_WriteReg(0xBD00,0x00);
        LCD_WriteReg(0xBD01,0x78);
        LCD_WriteReg(0xBD02,0x00);
        //VCOM
        LCD_WriteReg(0xBE00,0x00);
        LCD_WriteReg(0xBE01,0x64);
        //Gamma Setting
        LCD_WriteReg(0xD100,0x00);
        LCD_WriteReg(0xD101,0x33);
        LCD_WriteReg(0xD102,0x00);
        LCD_WriteReg(0xD103,0x34);
        LCD_WriteReg(0xD104,0x00);
        LCD_WriteReg(0xD105,0x3A);
        LCD_WriteReg(0xD106,0x00);
        LCD_WriteReg(0xD107,0x4A);
        LCD_WriteReg(0xD108,0x00);
        LCD_WriteReg(0xD109,0x5C);
        LCD_WriteReg(0xD10A,0x00);
        LCD_WriteReg(0xD10B,0x81);
        LCD_WriteReg(0xD10C,0x00);
        LCD_WriteReg(0xD10D,0xA6);
        LCD_WriteReg(0xD10E,0x00);
        LCD_WriteReg(0xD10F,0xE5);
        LCD_WriteReg(0xD110,0x01);
        LCD_WriteReg(0xD111,0x13);
        LCD_WriteReg(0xD112,0x01);
        LCD_WriteReg(0xD113,0x54);
        LCD_WriteReg(0xD114,0x01);
        LCD_WriteReg(0xD115,0x82);
        LCD_WriteReg(0xD116,0x01);
        LCD_WriteReg(0xD117,0xCA);
        LCD_WriteReg(0xD118,0x02);
        LCD_WriteReg(0xD119,0x00);
        LCD_WriteReg(0xD11A,0x02);
        LCD_WriteReg(0xD11B,0x01);
        LCD_WriteReg(0xD11C,0x02);
        LCD_WriteReg(0xD11D,0x34);
        LCD_WriteReg(0xD11E,0x02);
        LCD_WriteReg(0xD11F,0x67);
        LCD_WriteReg(0xD120,0x02);
        LCD_WriteReg(0xD121,0x84);
        LCD_WriteReg(0xD122,0x02);
        LCD_WriteReg(0xD123,0xA4);
        LCD_WriteReg(0xD124,0x02);
        LCD_WriteReg(0xD125,0xB7);
        LCD_WriteReg(0xD126,0x02);
        LCD_WriteReg(0xD127,0xCF);
        LCD_WriteReg(0xD128,0x02);
        LCD_WriteReg(0xD129,0xDE);
        LCD_WriteReg(0xD12A,0x02);
        LCD_WriteReg(0xD12B,0xF2);
        LCD_WriteReg(0xD12C,0x02);
        LCD_WriteReg(0xD12D,0xFE);
        LCD_WriteReg(0xD12E,0x03);
        LCD_WriteReg(0xD12F,0x10);
        LCD_WriteReg(0xD130,0x03);
        LCD_WriteReg(0xD131,0x33);
        LCD_WriteReg(0xD132,0x03);
        LCD_WriteReg(0xD133,0x6D);
        LCD_WriteReg(0xD200,0x00);
        LCD_WriteReg(0xD201,0x33);
        LCD_WriteReg(0xD202,0x00);
        LCD_WriteReg(0xD203,0x34);
        LCD_WriteReg(0xD204,0x00);
        LCD_WriteReg(0xD205,0x3A);
        LCD_WriteReg(0xD206,0x00);
        LCD_WriteReg(0xD207,0x4A);
        LCD_WriteReg(0xD208,0x00);
        LCD_WriteReg(0xD209,0x5C);
        LCD_WriteReg(0xD20A,0x00);

        LCD_WriteReg(0xD20B,0x81);
        LCD_WriteReg(0xD20C,0x00);
        LCD_WriteReg(0xD20D,0xA6);
        LCD_WriteReg(0xD20E,0x00);
        LCD_WriteReg(0xD20F,0xE5);
        LCD_WriteReg(0xD210,0x01);
        LCD_WriteReg(0xD211,0x13);
        LCD_WriteReg(0xD212,0x01);
        LCD_WriteReg(0xD213,0x54);
        LCD_WriteReg(0xD214,0x01);
        LCD_WriteReg(0xD215,0x82);
        LCD_WriteReg(0xD216,0x01);
        LCD_WriteReg(0xD217,0xCA);
        LCD_WriteReg(0xD218,0x02);
        LCD_WriteReg(0xD219,0x00);
        LCD_WriteReg(0xD21A,0x02);
        LCD_WriteReg(0xD21B,0x01);
        LCD_WriteReg(0xD21C,0x02);
        LCD_WriteReg(0xD21D,0x34);
        LCD_WriteReg(0xD21E,0x02);
        LCD_WriteReg(0xD21F,0x67);
        LCD_WriteReg(0xD220,0x02);
        LCD_WriteReg(0xD221,0x84);
        LCD_WriteReg(0xD222,0x02);
        LCD_WriteReg(0xD223,0xA4);
        LCD_WriteReg(0xD224,0x02);
        LCD_WriteReg(0xD225,0xB7);
        LCD_WriteReg(0xD226,0x02);
        LCD_WriteReg(0xD227,0xCF);
        LCD_WriteReg(0xD228,0x02);
        LCD_WriteReg(0xD229,0xDE);
        LCD_WriteReg(0xD22A,0x02);
        LCD_WriteReg(0xD22B,0xF2);
        LCD_WriteReg(0xD22C,0x02);
        LCD_WriteReg(0xD22D,0xFE);
        LCD_WriteReg(0xD22E,0x03);
        LCD_WriteReg(0xD22F,0x10);
        LCD_WriteReg(0xD230,0x03);
        LCD_WriteReg(0xD231,0x33);
        LCD_WriteReg(0xD232,0x03);
        LCD_WriteReg(0xD233,0x6D);
        LCD_WriteReg(0xD300,0x00);
        LCD_WriteReg(0xD301,0x33);
        LCD_WriteReg(0xD302,0x00);
        LCD_WriteReg(0xD303,0x34);
        LCD_WriteReg(0xD304,0x00);
        LCD_WriteReg(0xD305,0x3A);
        LCD_WriteReg(0xD306,0x00);
        LCD_WriteReg(0xD307,0x4A);
        LCD_WriteReg(0xD308,0x00);
        LCD_WriteReg(0xD309,0x5C);
        LCD_WriteReg(0xD30A,0x00);

        LCD_WriteReg(0xD30B,0x81);
        LCD_WriteReg(0xD30C,0x00);
        LCD_WriteReg(0xD30D,0xA6);
        LCD_WriteReg(0xD30E,0x00);
        LCD_WriteReg(0xD30F,0xE5);
        LCD_WriteReg(0xD310,0x01);
        LCD_WriteReg(0xD311,0x13);
        LCD_WriteReg(0xD312,0x01);
        LCD_WriteReg(0xD313,0x54);
        LCD_WriteReg(0xD314,0x01);
        LCD_WriteReg(0xD315,0x82);
        LCD_WriteReg(0xD316,0x01);
        LCD_WriteReg(0xD317,0xCA);
        LCD_WriteReg(0xD318,0x02);
        LCD_WriteReg(0xD319,0x00);
        LCD_WriteReg(0xD31A,0x02);
        LCD_WriteReg(0xD31B,0x01);
        LCD_WriteReg(0xD31C,0x02);
        LCD_WriteReg(0xD31D,0x34);
        LCD_WriteReg(0xD31E,0x02);
        LCD_WriteReg(0xD31F,0x67);
        LCD_WriteReg(0xD320,0x02);
        LCD_WriteReg(0xD321,0x84);
        LCD_WriteReg(0xD322,0x02);
        LCD_WriteReg(0xD323,0xA4);
        LCD_WriteReg(0xD324,0x02);
        LCD_WriteReg(0xD325,0xB7);
        LCD_WriteReg(0xD326,0x02);
        LCD_WriteReg(0xD327,0xCF);
        LCD_WriteReg(0xD328,0x02);
        LCD_WriteReg(0xD329,0xDE);
        LCD_WriteReg(0xD32A,0x02);
        LCD_WriteReg(0xD32B,0xF2);
        LCD_WriteReg(0xD32C,0x02);
        LCD_WriteReg(0xD32D,0xFE);
        LCD_WriteReg(0xD32E,0x03);
        LCD_WriteReg(0xD32F,0x10);
        LCD_WriteReg(0xD330,0x03);
        LCD_WriteReg(0xD331,0x33);
        LCD_WriteReg(0xD332,0x03);
        LCD_WriteReg(0xD333,0x6D);
        LCD_WriteReg(0xD400,0x00);
        LCD_WriteReg(0xD401,0x33);
        LCD_WriteReg(0xD402,0x00);
        LCD_WriteReg(0xD403,0x34);
        LCD_WriteReg(0xD404,0x00);
        LCD_WriteReg(0xD405,0x3A);
        LCD_WriteReg(0xD406,0x00);
        LCD_WriteReg(0xD407,0x4A);
        LCD_WriteReg(0xD408,0x00);
        LCD_WriteReg(0xD409,0x5C);
        LCD_WriteReg(0xD40A,0x00);
        LCD_WriteReg(0xD40B,0x81);

        LCD_WriteReg(0xD40C,0x00);
        LCD_WriteReg(0xD40D,0xA6);
        LCD_WriteReg(0xD40E,0x00);
        LCD_WriteReg(0xD40F,0xE5);
        LCD_WriteReg(0xD410,0x01);
        LCD_WriteReg(0xD411,0x13);
        LCD_WriteReg(0xD412,0x01);
        LCD_WriteReg(0xD413,0x54);
        LCD_WriteReg(0xD414,0x01);
        LCD_WriteReg(0xD415,0x82);
        LCD_WriteReg(0xD416,0x01);
        LCD_WriteReg(0xD417,0xCA);
        LCD_WriteReg(0xD418,0x02);
        LCD_WriteReg(0xD419,0x00);
        LCD_WriteReg(0xD41A,0x02);
        LCD_WriteReg(0xD41B,0x01);
        LCD_WriteReg(0xD41C,0x02);
        LCD_WriteReg(0xD41D,0x34);
        LCD_WriteReg(0xD41E,0x02);
        LCD_WriteReg(0xD41F,0x67);
        LCD_WriteReg(0xD420,0x02);
        LCD_WriteReg(0xD421,0x84);
        LCD_WriteReg(0xD422,0x02);
        LCD_WriteReg(0xD423,0xA4);
        LCD_WriteReg(0xD424,0x02);
        LCD_WriteReg(0xD425,0xB7);
        LCD_WriteReg(0xD426,0x02);
        LCD_WriteReg(0xD427,0xCF);
        LCD_WriteReg(0xD428,0x02);
        LCD_WriteReg(0xD429,0xDE);
        LCD_WriteReg(0xD42A,0x02);
        LCD_WriteReg(0xD42B,0xF2);
        LCD_WriteReg(0xD42C,0x02);
        LCD_WriteReg(0xD42D,0xFE);
        LCD_WriteReg(0xD42E,0x03);
        LCD_WriteReg(0xD42F,0x10);
        LCD_WriteReg(0xD430,0x03);
        LCD_WriteReg(0xD431,0x33);
        LCD_WriteReg(0xD432,0x03);
        LCD_WriteReg(0xD433,0x6D);
        LCD_WriteReg(0xD500,0x00);
        LCD_WriteReg(0xD501,0x33);
        LCD_WriteReg(0xD502,0x00);
        LCD_WriteReg(0xD503,0x34);
        LCD_WriteReg(0xD504,0x00);
        LCD_WriteReg(0xD505,0x3A);
        LCD_WriteReg(0xD506,0x00);
        LCD_WriteReg(0xD507,0x4A);
        LCD_WriteReg(0xD508,0x00);
        LCD_WriteReg(0xD509,0x5C);
        LCD_WriteReg(0xD50A,0x00);
        LCD_WriteReg(0xD50B,0x81);

        LCD_WriteReg(0xD50C,0x00);
        LCD_WriteReg(0xD50D,0xA6);
        LCD_WriteReg(0xD50E,0x00);
        LCD_WriteReg(0xD50F,0xE5);
        LCD_WriteReg(0xD510,0x01);
        LCD_WriteReg(0xD511,0x13);
        LCD_WriteReg(0xD512,0x01);
        LCD_WriteReg(0xD513,0x54);
        LCD_WriteReg(0xD514,0x01);
        LCD_WriteReg(0xD515,0x82);
        LCD_WriteReg(0xD516,0x01);
        LCD_WriteReg(0xD517,0xCA);
        LCD_WriteReg(0xD518,0x02);
        LCD_WriteReg(0xD519,0x00);
        LCD_WriteReg(0xD51A,0x02);
        LCD_WriteReg(0xD51B,0x01);
        LCD_WriteReg(0xD51C,0x02);
        LCD_WriteReg(0xD51D,0x34);
        LCD_WriteReg(0xD51E,0x02);
        LCD_WriteReg(0xD51F,0x67);
        LCD_WriteReg(0xD520,0x02);
        LCD_WriteReg(0xD521,0x84);
        LCD_WriteReg(0xD522,0x02);
        LCD_WriteReg(0xD523,0xA4);
        LCD_WriteReg(0xD524,0x02);
        LCD_WriteReg(0xD525,0xB7);
        LCD_WriteReg(0xD526,0x02);
        LCD_WriteReg(0xD527,0xCF);
        LCD_WriteReg(0xD528,0x02);
        LCD_WriteReg(0xD529,0xDE);
        LCD_WriteReg(0xD52A,0x02);
        LCD_WriteReg(0xD52B,0xF2);
        LCD_WriteReg(0xD52C,0x02);
        LCD_WriteReg(0xD52D,0xFE);
        LCD_WriteReg(0xD52E,0x03);
        LCD_WriteReg(0xD52F,0x10);
        LCD_WriteReg(0xD530,0x03);
        LCD_WriteReg(0xD531,0x33);
        LCD_WriteReg(0xD532,0x03);
        LCD_WriteReg(0xD533,0x6D);
        LCD_WriteReg(0xD600,0x00);
        LCD_WriteReg(0xD601,0x33);
        LCD_WriteReg(0xD602,0x00);
        LCD_WriteReg(0xD603,0x34);
        LCD_WriteReg(0xD604,0x00);
        LCD_WriteReg(0xD605,0x3A);
        LCD_WriteReg(0xD606,0x00);
        LCD_WriteReg(0xD607,0x4A);
        LCD_WriteReg(0xD608,0x00);
        LCD_WriteReg(0xD609,0x5C);
        LCD_WriteReg(0xD60A,0x00);
        LCD_WriteReg(0xD60B,0x81);

        LCD_WriteReg(0xD60C,0x00);
        LCD_WriteReg(0xD60D,0xA6);
        LCD_WriteReg(0xD60E,0x00);
        LCD_WriteReg(0xD60F,0xE5);
        LCD_WriteReg(0xD610,0x01);
        LCD_WriteReg(0xD611,0x13);
        LCD_WriteReg(0xD612,0x01);
        LCD_WriteReg(0xD613,0x54);
        LCD_WriteReg(0xD614,0x01);
        LCD_WriteReg(0xD615,0x82);
        LCD_WriteReg(0xD616,0x01);
        LCD_WriteReg(0xD617,0xCA);
        LCD_WriteReg(0xD618,0x02);
        LCD_WriteReg(0xD619,0x00);
        LCD_WriteReg(0xD61A,0x02);
        LCD_WriteReg(0xD61B,0x01);
        LCD_WriteReg(0xD61C,0x02);
        LCD_WriteReg(0xD61D,0x34);
        LCD_WriteReg(0xD61E,0x02);
        LCD_WriteReg(0xD61F,0x67);
        LCD_WriteReg(0xD620,0x02);
        LCD_WriteReg(0xD621,0x84);
        LCD_WriteReg(0xD622,0x02);
        LCD_WriteReg(0xD623,0xA4);
        LCD_WriteReg(0xD624,0x02);
        LCD_WriteReg(0xD625,0xB7);
        LCD_WriteReg(0xD626,0x02);
        LCD_WriteReg(0xD627,0xCF);
        LCD_WriteReg(0xD628,0x02);
        LCD_WriteReg(0xD629,0xDE);
        LCD_WriteReg(0xD62A,0x02);
        LCD_WriteReg(0xD62B,0xF2);
        LCD_WriteReg(0xD62C,0x02);
        LCD_WriteReg(0xD62D,0xFE);
        LCD_WriteReg(0xD62E,0x03);
        LCD_WriteReg(0xD62F,0x10);
        LCD_WriteReg(0xD630,0x03);
        LCD_WriteReg(0xD631,0x33);
        LCD_WriteReg(0xD632,0x03);
        LCD_WriteReg(0xD633,0x6D);
        //LV2 Page 0 enable
        LCD_WriteReg(0xF000,0x55);
        LCD_WriteReg(0xF001,0xAA);
        LCD_WriteReg(0xF002,0x52);
        LCD_WriteReg(0xF003,0x08);
        LCD_WriteReg(0xF004,0x00);
        //Display control
        LCD_WriteReg(0xB100, 0xCC);
        LCD_WriteReg(0xB101, 0x00);
        //Source hold time
        LCD_WriteReg(0xB600,0x05);
        //Gate EQ control
        LCD_WriteReg(0xB700,0x70);
        LCD_WriteReg(0xB701,0x70);
        //Source EQ control (Mode 2)
        LCD_WriteReg(0xB800,0x01);
        LCD_WriteReg(0xB801,0x03);
        LCD_WriteReg(0xB802,0x03);
        LCD_WriteReg(0xB803,0x03);
        //Inversion mode (2-dot)
        LCD_WriteReg(0xBC00,0x02);
        LCD_WriteReg(0xBC01,0x00);
        LCD_WriteReg(0xBC02,0x00);
        //Timing control 4H w/ 4-delay
        LCD_WriteReg(0xC900,0xD0);
        LCD_WriteReg(0xC901,0x02);
        LCD_WriteReg(0xC902,0x50);
        LCD_WriteReg(0xC903,0x50);
        LCD_WriteReg(0xC904,0x50);
        LCD_WriteReg(0x3500,0x00);
        LCD_WriteReg(0x3A00,0x55);  //16-bit/pixel
        LCD_WR_REG(0x1100);
        delay_us(120);
        LCD_WR_REG(0x2900);
    }else if(lcddev.id==0x9325)//9325
    {
        LCD_WriteReg(0x00E5,0x78F0); 
        LCD_WriteReg(0x0001,0x0100); 
        LCD_WriteReg(0x0002,0x0700); 
        LCD_WriteReg(0x0003,0x1030); 
        LCD_WriteReg(0x0004,0x0000); 
        LCD_WriteReg(0x0008,0x0202);  
        LCD_WriteReg(0x0009,0x0000);
        LCD_WriteReg(0x000A,0x0000); 
        LCD_WriteReg(0x000C,0x0000); 
        LCD_WriteReg(0x000D,0x0000);
        LCD_WriteReg(0x000F,0x0000);
        //power on sequence VGHVGL
        LCD_WriteReg(0x0010,0x0000);   
        LCD_WriteReg(0x0011,0x0007);  
        LCD_WriteReg(0x0012,0x0000);  
        LCD_WriteReg(0x0013,0x0000); 
        LCD_WriteReg(0x0007,0x0000); 
        //vgh 
        LCD_WriteReg(0x0010,0x1690);   
        LCD_WriteReg(0x0011,0x0227);
        //delayms(100);
        //vregiout 
        LCD_WriteReg(0x0012,0x009D); //0x001b
        //delayms(100); 
        //vom amplitude
        LCD_WriteReg(0x0013,0x1900);
        //delayms(100); 
        //vom H
        LCD_WriteReg(0x0029,0x0025); 
        LCD_WriteReg(0x002B,0x000D); 
        //gamma
        LCD_WriteReg(0x0030,0x0007);
        LCD_WriteReg(0x0031,0x0303);
        LCD_WriteReg(0x0032,0x0003);// 0006
        LCD_WriteReg(0x0035,0x0206);
        LCD_WriteReg(0x0036,0x0008);
        LCD_WriteReg(0x0037,0x0406); 
        LCD_WriteReg(0x0038,0x0304);//0200
        LCD_WriteReg(0x0039,0x0007); 
        LCD_WriteReg(0x003C,0x0602);// 0504
        LCD_WriteReg(0x003D,0x0008); 
        //ram
        LCD_WriteReg(0x0050,0x0000); 
        LCD_WriteReg(0x0051,0x00EF);
        LCD_WriteReg(0x0052,0x0000); 
        LCD_WriteReg(0x0053,0x013F);  
        LCD_WriteReg(0x0060,0xA700); 
        LCD_WriteReg(0x0061,0x0001); 
        LCD_WriteReg(0x006A,0x0000); 
        //
        LCD_WriteReg(0x0080,0x0000); 
        LCD_WriteReg(0x0081,0x0000); 
        LCD_WriteReg(0x0082,0x0000); 
        LCD_WriteReg(0x0083,0x0000); 
        LCD_WriteReg(0x0084,0x0000); 
        LCD_WriteReg(0x0085,0x0000); 
        //
        LCD_WriteReg(0x0090,0x0010); 
        LCD_WriteReg(0x0092,0x0600); 
        
        LCD_WriteReg(0x0007,0x0133);
        LCD_WriteReg(0x00,0x0022);//
    }else if(lcddev.id==0x9328)//ILI9328   OK  
    {
          LCD_WriteReg(0x00EC,0x108F);// internal timeing      
         LCD_WriteReg(0x00EF,0x1234);// ADD        
        //LCD_WriteReg(0x00e7,0x0010);      
        //LCD_WriteReg(0x0000,0x0001);//开启内部时钟
        LCD_WriteReg(0x0001,0x0100);     
        LCD_WriteReg(0x0002,0x0700);//电源开启                    
        //LCD_WriteReg(0x0003,(1<<3)|(1<<4) );     //65K  RGB
        //DRIVE TABLE(寄存器 03H)
        //BIT3=AM BIT4:5=ID0:1
        //AM ID0 ID1   FUNCATION
        // 0  0   0       R->L D->U
        // 1  0   0       D->U    R->L
        // 0  1   0       L->R D->U
        // 1  1   0    D->U    L->R
        // 0  0   1       R->L U->D
        // 1  0   1    U->D    R->L
        // 0  1   1    L->R U->D 正常就用这个.
        // 1  1   1       U->D    L->R
        LCD_WriteReg(0x0003,(1<<12)|(3<<4)|(0<<3) );//65K    
        LCD_WriteReg(0x0004,0x0000);                                   
        LCD_WriteReg(0x0008,0x0202);               
        LCD_WriteReg(0x0009,0x0000);         
        LCD_WriteReg(0x000a,0x0000);//display setting         
        LCD_WriteReg(0x000c,0x0001);//display setting          
        LCD_WriteReg(0x000d,0x0000);//0f3c          
        LCD_WriteReg(0x000f,0x0000);
        //电源配置
        LCD_WriteReg(0x0010,0x0000);   
        LCD_WriteReg(0x0011,0x0007);
        LCD_WriteReg(0x0012,0x0000);                                                                 
        LCD_WriteReg(0x0013,0x0000);                 
         LCD_WriteReg(0x0007,0x0001);                 
           delay_ms(50); 
        LCD_WriteReg(0x0010,0x1490);   
        LCD_WriteReg(0x0011,0x0227);
        delay_ms(50); 
        LCD_WriteReg(0x0012,0x008A);                  
        delay_ms(50); 
        LCD_WriteReg(0x0013,0x1a00);   
        LCD_WriteReg(0x0029,0x0006);
        LCD_WriteReg(0x002b,0x000d);
        delay_ms(50); 
        LCD_WriteReg(0x0020,0x0000);                                                            
        LCD_WriteReg(0x0021,0x0000);           
        delay_ms(50); 
        //伽马校正
        LCD_WriteReg(0x0030,0x0000); 
        LCD_WriteReg(0x0031,0x0604);   
        LCD_WriteReg(0x0032,0x0305);
        LCD_WriteReg(0x0035,0x0000);
        LCD_WriteReg(0x0036,0x0C09); 
        LCD_WriteReg(0x0037,0x0204);
        LCD_WriteReg(0x0038,0x0301);        
        LCD_WriteReg(0x0039,0x0707);     
        LCD_WriteReg(0x003c,0x0000);
        LCD_WriteReg(0x003d,0x0a0a);
        delay_ms(50); 
        LCD_WriteReg(0x0050,0x0000); //水平GRAM起始位置 
        LCD_WriteReg(0x0051,0x00ef); //水平GRAM终止位置                    
        LCD_WriteReg(0x0052,0x0000); //垂直GRAM起始位置                    
        LCD_WriteReg(0x0053,0x013f); //垂直GRAM终止位置  
 
         LCD_WriteReg(0x0060,0xa700);        
        LCD_WriteReg(0x0061,0x0001); 
        LCD_WriteReg(0x006a,0x0000);
        LCD_WriteReg(0x0080,0x0000);
        LCD_WriteReg(0x0081,0x0000);
        LCD_WriteReg(0x0082,0x0000);
        LCD_WriteReg(0x0083,0x0000);
        LCD_WriteReg(0x0084,0x0000);
        LCD_WriteReg(0x0085,0x0000);
      
        LCD_WriteReg(0x0090,0x0010);     
        LCD_WriteReg(0x0092,0x0600);  
        //开启显示设置    
        LCD_WriteReg(0x0007,0x0133); 
    }else if(lcddev.id==0x9320)//测试OK.
    {
        LCD_WriteReg(0x00,0x0000);
        LCD_WriteReg(0x01,0x0100);    //Driver Output Contral.
        LCD_WriteReg(0x02,0x0700);    //LCD Driver Waveform Contral.
        LCD_WriteReg(0x03,0x1030);//Entry Mode Set.
        //LCD_WriteReg(0x03,0x1018);    //Entry Mode Set.
    
        LCD_WriteReg(0x04,0x0000);    //Scalling Contral.
        LCD_WriteReg(0x08,0x0202);    //Display Contral 2.(0x0207)
        LCD_WriteReg(0x09,0x0000);    //Display Contral 3.(0x0000)
        LCD_WriteReg(0x0a,0x0000);    //Frame Cycle Contal.(0x0000)
        LCD_WriteReg(0x0c,(1<<0));    //Extern Display Interface Contral 1.(0x0000)
        LCD_WriteReg(0x0d,0x0000);    //Frame Maker Position.
        LCD_WriteReg(0x0f,0x0000);    //Extern Display Interface Contral 2.        
        delay_ms(50); 
        LCD_WriteReg(0x07,0x0101);    //Display Contral.
        delay_ms(50);                                   
        LCD_WriteReg(0x10,(1<<12)|(0<<8)|(1<<7)|(1<<6)|(0<<4));    //Power Control 1.(0x16b0)
        LCD_WriteReg(0x11,0x0007);                                //Power Control 2.(0x0001)
        LCD_WriteReg(0x12,(1<<8)|(1<<4)|(0<<0));                //Power Control 3.(0x0138)
        LCD_WriteReg(0x13,0x0b00);                                //Power Control 4.
        LCD_WriteReg(0x29,0x0000);                                //Power Control 7.
    
        LCD_WriteReg(0x2b,(1<<14)|(1<<4));        
        LCD_WriteReg(0x50,0);    //Set X Star
        //水平GRAM终止位置Set X End.
        LCD_WriteReg(0x51,239);    //Set Y Star
        LCD_WriteReg(0x52,0);    //Set Y End.t.
        LCD_WriteReg(0x53,319);    //
    
        LCD_WriteReg(0x60,0x2700);    //Driver Output Control.
        LCD_WriteReg(0x61,0x0001);    //Driver Output Control.
        LCD_WriteReg(0x6a,0x0000);    //Vertical Srcoll Control.
    
        LCD_WriteReg(0x80,0x0000);    //Display Position? Partial Display 1.
        LCD_WriteReg(0x81,0x0000);    //RAM Address Start? Partial Display 1.
        LCD_WriteReg(0x82,0x0000);    //RAM Address End-Partial Display 1.
        LCD_WriteReg(0x83,0x0000);    //Displsy Position? Partial Display 2.
        LCD_WriteReg(0x84,0x0000);    //RAM Address Start? Partial Display 2.
        LCD_WriteReg(0x85,0x0000);    //RAM Address End? Partial Display 2.
    
        LCD_WriteReg(0x90,(0<<7)|(16<<0));    //Frame Cycle Contral.(0x0013)
        LCD_WriteReg(0x92,0x0000);    //Panel Interface Contral 2.(0x0000)
        LCD_WriteReg(0x93,0x0001);    //Panel Interface Contral 3.
        LCD_WriteReg(0x95,0x0110);    //Frame Cycle Contral.(0x0110)
        LCD_WriteReg(0x97,(0<<8));    //
        LCD_WriteReg(0x98,0x0000);    //Frame Cycle Contral.       
        LCD_WriteReg(0x07,0x0173);    //(0x0173)
    }else if(lcddev.id==0X9331)//OK |/|/|             
    {
        LCD_WriteReg(0x00E7, 0x1014);
        LCD_WriteReg(0x0001, 0x0100); // set SS and SM bit
        LCD_WriteReg(0x0002, 0x0200); // set 1 line inversion
        LCD_WriteReg(0x0003,(1<<12)|(3<<4)|(1<<3));//65K    
        //LCD_WriteReg(0x0003, 0x1030); // set GRAM write direction and BGR=1.
        LCD_WriteReg(0x0008, 0x0202); // set the back porch and front porch
        LCD_WriteReg(0x0009, 0x0000); // set non-display area refresh cycle ISC[3:0]
        LCD_WriteReg(0x000A, 0x0000); // FMARK function
        LCD_WriteReg(0x000C, 0x0000); // RGB interface setting
        LCD_WriteReg(0x000D, 0x0000); // Frame marker Position
        LCD_WriteReg(0x000F, 0x0000); // RGB interface polarity
        //*************Power On sequence ****************//
        LCD_WriteReg(0x0010, 0x0000); // SAP, BT[3:0], AP, DSTB, SLP, STB
        LCD_WriteReg(0x0011, 0x0007); // DC1[2:0], DC0[2:0], VC[2:0]
        LCD_WriteReg(0x0012, 0x0000); // VREG1OUT voltage
        LCD_WriteReg(0x0013, 0x0000); // VDV[4:0] for VCOM amplitude
        delay_ms(200); // Dis-charge capacitor power voltage
        LCD_WriteReg(0x0010, 0x1690); // SAP, BT[3:0], AP, DSTB, SLP, STB
        LCD_WriteReg(0x0011, 0x0227); // DC1[2:0], DC0[2:0], VC[2:0]
        delay_ms(50); // Delay 50ms
        LCD_WriteReg(0x0012, 0x000C); // Internal reference voltage= Vci;
        delay_ms(50); // Delay 50ms
        LCD_WriteReg(0x0013, 0x0800); // Set VDV[4:0] for VCOM amplitude
        LCD_WriteReg(0x0029, 0x0011); // Set VCM[5:0] for VCOMH
        LCD_WriteReg(0x002B, 0x000B); // Set Frame Rate
        delay_ms(50); // Delay 50ms
        LCD_WriteReg(0x0020, 0x0000); // GRAM horizontal Address
        LCD_WriteReg(0x0021, 0x013f); // GRAM Vertical Address
        // ----------- Adjust the Gamma Curve ----------//
        LCD_WriteReg(0x0030, 0x0000);
        LCD_WriteReg(0x0031, 0x0106);
        LCD_WriteReg(0x0032, 0x0000);
        LCD_WriteReg(0x0035, 0x0204);
        LCD_WriteReg(0x0036, 0x160A);
        LCD_WriteReg(0x0037, 0x0707);
        LCD_WriteReg(0x0038, 0x0106);
        LCD_WriteReg(0x0039, 0x0707);
        LCD_WriteReg(0x003C, 0x0402);
        LCD_WriteReg(0x003D, 0x0C0F);
        //------------------ Set GRAM area ---------------//
        LCD_WriteReg(0x0050, 0x0000); // Horizontal GRAM Start Address
        LCD_WriteReg(0x0051, 0x00EF); // Horizontal GRAM End Address
        LCD_WriteReg(0x0052, 0x0000); // Vertical GRAM Start Address
        LCD_WriteReg(0x0053, 0x013F); // Vertical GRAM Start Address
        LCD_WriteReg(0x0060, 0x2700); // Gate Scan Line
        LCD_WriteReg(0x0061, 0x0001); // NDL,VLE, REV 
        LCD_WriteReg(0x006A, 0x0000); // set scrolling line
        //-------------- Partial Display Control ---------//
        LCD_WriteReg(0x0080, 0x0000);
        LCD_WriteReg(0x0081, 0x0000);
        LCD_WriteReg(0x0082, 0x0000);
        LCD_WriteReg(0x0083, 0x0000);
        LCD_WriteReg(0x0084, 0x0000);
        LCD_WriteReg(0x0085, 0x0000);
        //-------------- Panel Control -------------------//
        LCD_WriteReg(0x0090, 0x0010);
        LCD_WriteReg(0x0092, 0x0600);
        LCD_WriteReg(0x0007, 0x0133); // 262K color and display ON
    }else if(lcddev.id==0x5408)
    {
        LCD_WriteReg(0x01,0x0100);                                  
        LCD_WriteReg(0x02,0x0700);//LCD Driving Waveform Contral 
        LCD_WriteReg(0x03,0x1030);//Entry Mode设置        
        //指针从左至右自上而下的自动增模式
        //Normal Mode(Window Mode disable)
        //RGB格式
        //16位数据2次传输的8总线设置
        LCD_WriteReg(0x04,0x0000); //Scalling Control register     
        LCD_WriteReg(0x08,0x0207); //Display Control 2 
        LCD_WriteReg(0x09,0x0000); //Display Control 3     
        LCD_WriteReg(0x0A,0x0000); //Frame Cycle Control     
        LCD_WriteReg(0x0C,0x0000); //External Display Interface Control 1 
        LCD_WriteReg(0x0D,0x0000); //Frame Maker Position         
        LCD_WriteReg(0x0F,0x0000); //External Display Interface Control 2 
         delay_ms(20);
        //TFT 液晶彩色图像显示方法14
        LCD_WriteReg(0x10,0x16B0); //0x14B0 //Power Control 1
        LCD_WriteReg(0x11,0x0001); //0x0007 //Power Control 2
        LCD_WriteReg(0x17,0x0001); //0x0000 //Power Control 3
        LCD_WriteReg(0x12,0x0138); //0x013B //Power Control 4
        LCD_WriteReg(0x13,0x0800); //0x0800 //Power Control 5
        LCD_WriteReg(0x29,0x0009); //NVM read data 2
        LCD_WriteReg(0x2a,0x0009); //NVM read data 3
        LCD_WriteReg(0xa4,0x0000);     
        LCD_WriteReg(0x50,0x0000); //设置操作窗口的X轴开始列
        LCD_WriteReg(0x51,0x00EF); //设置操作窗口的X轴结束列
        LCD_WriteReg(0x52,0x0000); //设置操作窗口的Y轴开始行
        LCD_WriteReg(0x53,0x013F); //设置操作窗口的Y轴结束行
        LCD_WriteReg(0x60,0x2700); //Driver Output Control
        //设置屏幕的点数以及扫描的起始行
        LCD_WriteReg(0x61,0x0001); //Driver Output Control
        LCD_WriteReg(0x6A,0x0000); //Vertical Scroll Control
        LCD_WriteReg(0x80,0x0000); //Display Position – Partial Display 1
        LCD_WriteReg(0x81,0x0000); //RAM Address Start – Partial Display 1
        LCD_WriteReg(0x82,0x0000); //RAM address End - Partial Display 1
        LCD_WriteReg(0x83,0x0000); //Display Position – Partial Display 2
        LCD_WriteReg(0x84,0x0000); //RAM Address Start – Partial Display 2
        LCD_WriteReg(0x85,0x0000); //RAM address End – Partail Display2
        LCD_WriteReg(0x90,0x0013); //Frame Cycle Control
        LCD_WriteReg(0x92,0x0000);  //Panel Interface Control 2
        LCD_WriteReg(0x93,0x0003); //Panel Interface control 3
        LCD_WriteReg(0x95,0x0110);  //Frame Cycle Control
        LCD_WriteReg(0x07,0x0173);         
        delay_ms(50);
    }    
    else if(lcddev.id==0x1505)//OK
    {
        // second release on 3/5  ,luminance is acceptable,water wave appear during camera preview
        LCD_WriteReg(0x0007,0x0000);
        delay_ms(50); 
        LCD_WriteReg(0x0012,0x011C);//0x011A   why need to set several times?
        LCD_WriteReg(0x00A4,0x0001);//NVM     
        LCD_WriteReg(0x0008,0x000F);
        LCD_WriteReg(0x000A,0x0008);
        LCD_WriteReg(0x000D,0x0008);        
          //伽马校正
        LCD_WriteReg(0x0030,0x0707);
        LCD_WriteReg(0x0031,0x0007); //0x0707
        LCD_WriteReg(0x0032,0x0603); 
        LCD_WriteReg(0x0033,0x0700); 
        LCD_WriteReg(0x0034,0x0202); 
        LCD_WriteReg(0x0035,0x0002); //?0x0606
        LCD_WriteReg(0x0036,0x1F0F);
        LCD_WriteReg(0x0037,0x0707); //0x0f0f  0x0105
        LCD_WriteReg(0x0038,0x0000); 
        LCD_WriteReg(0x0039,0x0000); 
        LCD_WriteReg(0x003A,0x0707); 
        LCD_WriteReg(0x003B,0x0000); //0x0303
        LCD_WriteReg(0x003C,0x0007); //?0x0707
        LCD_WriteReg(0x003D,0x0000); //0x1313//0x1f08
        delay_ms(50); 
        LCD_WriteReg(0x0007,0x0001);
        LCD_WriteReg(0x0017,0x0001);//开启电源
        delay_ms(50); 
          //电源配置
        LCD_WriteReg(0x0010,0x17A0); 
        LCD_WriteReg(0x0011,0x0217);//reference voltage VC[2:0]   Vciout = 1.00*Vcivl
        LCD_WriteReg(0x0012,0x011E);//0x011c  //Vreg1out = Vcilvl*1.80   is it the same as Vgama1out ?
        LCD_WriteReg(0x0013,0x0F00);//VDV[4:0]-->VCOM Amplitude VcomL = VcomH - Vcom Ampl
        LCD_WriteReg(0x002A,0x0000);  
        LCD_WriteReg(0x0029,0x000A);//0x0001F  Vcomh = VCM1[4:0]*Vreg1out    gate source voltage??
        LCD_WriteReg(0x0012,0x013E);// 0x013C  power supply on
        //Coordinates Control//
        LCD_WriteReg(0x0050,0x0000);//0x0e00
        LCD_WriteReg(0x0051,0x00EF); 
        LCD_WriteReg(0x0052,0x0000); 
        LCD_WriteReg(0x0053,0x013F); 
        //Pannel Image Control//
        LCD_WriteReg(0x0060,0x2700); 
        LCD_WriteReg(0x0061,0x0001); 
        LCD_WriteReg(0x006A,0x0000); 
        LCD_WriteReg(0x0080,0x0000); 
        //Partial Image Control//
        LCD_WriteReg(0x0081,0x0000); 
        LCD_WriteReg(0x0082,0x0000); 
        LCD_WriteReg(0x0083,0x0000); 
        LCD_WriteReg(0x0084,0x0000); 
        LCD_WriteReg(0x0085,0x0000); 
          //Panel Interface Control//
        LCD_WriteReg(0x0090,0x0013);//0x0010 frenqucy
        LCD_WriteReg(0x0092,0x0300); 
        LCD_WriteReg(0x0093,0x0005); 
        LCD_WriteReg(0x0095,0x0000); 
        LCD_WriteReg(0x0097,0x0000); 
        LCD_WriteReg(0x0098,0x0000); 
  
        LCD_WriteReg(0x0001,0x0100); 
        LCD_WriteReg(0x0002,0x0700); 
        LCD_WriteReg(0x0003,0x1038);//扫描方向 上->下  左->右 
        LCD_WriteReg(0x0004,0x0000); 
        LCD_WriteReg(0x000C,0x0000); 
        LCD_WriteReg(0x000F,0x0000); 
        LCD_WriteReg(0x0020,0x0000); 
        LCD_WriteReg(0x0021,0x0000); 
        LCD_WriteReg(0x0007,0x0021); 
        delay_ms(20);
        LCD_WriteReg(0x0007,0x0061); 
        delay_ms(20);
        LCD_WriteReg(0x0007,0x0173); 
        delay_ms(20);
    }else if(lcddev.id==0xB505)
    {
        LCD_WriteReg(0x0000,0x0000);
        LCD_WriteReg(0x0000,0x0000);
        LCD_WriteReg(0x0000,0x0000);
        LCD_WriteReg(0x0000,0x0000);
        
        LCD_WriteReg(0x00a4,0x0001);
        delay_ms(20);          
        LCD_WriteReg(0x0060,0x2700);
        LCD_WriteReg(0x0008,0x0202);
        
        LCD_WriteReg(0x0030,0x0214);
        LCD_WriteReg(0x0031,0x3715);
        LCD_WriteReg(0x0032,0x0604);
        LCD_WriteReg(0x0033,0x0e16);
        LCD_WriteReg(0x0034,0x2211);
        LCD_WriteReg(0x0035,0x1500);
        LCD_WriteReg(0x0036,0x8507);
        LCD_WriteReg(0x0037,0x1407);
        LCD_WriteReg(0x0038,0x1403);
        LCD_WriteReg(0x0039,0x0020);
        
        LCD_WriteReg(0x0090,0x001a);
        LCD_WriteReg(0x0010,0x0000);
        LCD_WriteReg(0x0011,0x0007);
        LCD_WriteReg(0x0012,0x0000);
        LCD_WriteReg(0x0013,0x0000);
        delay_ms(20);
        
        LCD_WriteReg(0x0010,0x0730);
        LCD_WriteReg(0x0011,0x0137);
        delay_ms(20);
        
        LCD_WriteReg(0x0012,0x01b8);
        delay_ms(20);
        
        LCD_WriteReg(0x0013,0x0f00);
        LCD_WriteReg(0x002a,0x0080);
        LCD_WriteReg(0x0029,0x0048);
        delay_ms(20);
        
        LCD_WriteReg(0x0001,0x0100);
        LCD_WriteReg(0x0002,0x0700);
        LCD_WriteReg(0x0003,0x1038);//扫描方向 上->下  左->右 
        LCD_WriteReg(0x0008,0x0202);
        LCD_WriteReg(0x000a,0x0000);
        LCD_WriteReg(0x000c,0x0000);
        LCD_WriteReg(0x000d,0x0000);
        LCD_WriteReg(0x000e,0x0030);
        LCD_WriteReg(0x0050,0x0000);
        LCD_WriteReg(0x0051,0x00ef);
        LCD_WriteReg(0x0052,0x0000);
        LCD_WriteReg(0x0053,0x013f);
        LCD_WriteReg(0x0060,0x2700);
        LCD_WriteReg(0x0061,0x0001);
        LCD_WriteReg(0x006a,0x0000);
        //LCD_WriteReg(0x0080,0x0000);
        //LCD_WriteReg(0x0081,0x0000);
        LCD_WriteReg(0x0090,0X0011);
        LCD_WriteReg(0x0092,0x0600);
        LCD_WriteReg(0x0093,0x0402);
        LCD_WriteReg(0x0094,0x0002);
        delay_ms(20);
        
        LCD_WriteReg(0x0007,0x0001);
        delay_ms(20);
        LCD_WriteReg(0x0007,0x0061);
        LCD_WriteReg(0x0007,0x0173);
        
        LCD_WriteReg(0x0020,0x0000);
        LCD_WriteReg(0x0021,0x0000);      
        LCD_WriteReg(0x00,0x22);  
    }else if(lcddev.id==0xC505)
    {
        LCD_WriteReg(0x0000,0x0000);
        LCD_WriteReg(0x0000,0x0000);
        delay_ms(20);          
        LCD_WriteReg(0x0000,0x0000);
        LCD_WriteReg(0x0000,0x0000);
        LCD_WriteReg(0x0000,0x0000);
        LCD_WriteReg(0x0000,0x0000);
         LCD_WriteReg(0x00a4,0x0001);
        delay_ms(20);          
        LCD_WriteReg(0x0060,0x2700);
        LCD_WriteReg(0x0008,0x0806);
        
        LCD_WriteReg(0x0030,0x0703);//gamma setting
        LCD_WriteReg(0x0031,0x0001);
        LCD_WriteReg(0x0032,0x0004);
        LCD_WriteReg(0x0033,0x0102);
        LCD_WriteReg(0x0034,0x0300);
        LCD_WriteReg(0x0035,0x0103);
        LCD_WriteReg(0x0036,0x001F);
        LCD_WriteReg(0x0037,0x0703);
        LCD_WriteReg(0x0038,0x0001);
        LCD_WriteReg(0x0039,0x0004);
        
        
        
        LCD_WriteReg(0x0090, 0x0015);    //80Hz
        LCD_WriteReg(0x0010, 0X0410);    //BT,AP
        LCD_WriteReg(0x0011,0x0247);    //DC1,DC0,VC
        LCD_WriteReg(0x0012, 0x01BC);
        LCD_WriteReg(0x0013, 0x0e00);
        delay_ms(120);
        LCD_WriteReg(0x0001, 0x0100);
        LCD_WriteReg(0x0002, 0x0200);
        LCD_WriteReg(0x0003, 0x1030);
        
        LCD_WriteReg(0x000A, 0x0008);
        LCD_WriteReg(0x000C, 0x0000);
        
        LCD_WriteReg(0x000E, 0x0020);
        LCD_WriteReg(0x000F, 0x0000);
        LCD_WriteReg(0x0020, 0x0000);    //H Start
        LCD_WriteReg(0x0021, 0x0000);    //V Start
        LCD_WriteReg(0x002A,0x003D);    //vcom2
        delay_ms(20);
        LCD_WriteReg(0x0029, 0x002d);
        LCD_WriteReg(0x0050, 0x0000);
        LCD_WriteReg(0x0051, 0xD0EF);
        LCD_WriteReg(0x0052, 0x0000);
        LCD_WriteReg(0x0053, 0x013F);
        LCD_WriteReg(0x0061, 0x0000);
        LCD_WriteReg(0x006A, 0x0000);
        LCD_WriteReg(0x0092,0x0300); 
 
         LCD_WriteReg(0x0093, 0x0005);
        LCD_WriteReg(0x0007, 0x0100);
    }else if(lcddev.id==0x4531)//OK |/|/|
    {
        LCD_WriteReg(0X00,0X0001);   
        delay_ms(10);   
        LCD_WriteReg(0X10,0X1628);   
        LCD_WriteReg(0X12,0X000e);//0x0006    
        LCD_WriteReg(0X13,0X0A39);   
        delay_ms(10);   
        LCD_WriteReg(0X11,0X0040);   
        LCD_WriteReg(0X15,0X0050);   
        delay_ms(10);   
        LCD_WriteReg(0X12,0X001e);//16    
        delay_ms(10);   
        LCD_WriteReg(0X10,0X1620);   
        LCD_WriteReg(0X13,0X2A39);   
        delay_ms(10);   
        LCD_WriteReg(0X01,0X0100);   
        LCD_WriteReg(0X02,0X0300);   
        LCD_WriteReg(0X03,0X1038);//改变方向的   
        LCD_WriteReg(0X08,0X0202);   
        LCD_WriteReg(0X0A,0X0008);   
        LCD_WriteReg(0X30,0X0000);   
        LCD_WriteReg(0X31,0X0402);   
        LCD_WriteReg(0X32,0X0106);   
        LCD_WriteReg(0X33,0X0503);   
        LCD_WriteReg(0X34,0X0104);   
        LCD_WriteReg(0X35,0X0301);   
        LCD_WriteReg(0X36,0X0707);   
        LCD_WriteReg(0X37,0X0305);   
        LCD_WriteReg(0X38,0X0208);   
        LCD_WriteReg(0X39,0X0F0B);   
        LCD_WriteReg(0X41,0X0002);   
        LCD_WriteReg(0X60,0X2700);   
        LCD_WriteReg(0X61,0X0001);   
        LCD_WriteReg(0X90,0X0210);   
        LCD_WriteReg(0X92,0X010A);   
        LCD_WriteReg(0X93,0X0004);   
        LCD_WriteReg(0XA0,0X0100);   
        LCD_WriteReg(0X07,0X0001);   
        LCD_WriteReg(0X07,0X0021);   
        LCD_WriteReg(0X07,0X0023);   
        LCD_WriteReg(0X07,0X0033);   
        LCD_WriteReg(0X07,0X0133);   
        LCD_WriteReg(0XA0,0X0000); 
    }else if(lcddev.id==0x4535)
    {                  
        LCD_WriteReg(0X15,0X0030);   
        LCD_WriteReg(0X9A,0X0010);   
         LCD_WriteReg(0X11,0X0020);   
         LCD_WriteReg(0X10,0X3428);   
        LCD_WriteReg(0X12,0X0002);//16    
         LCD_WriteReg(0X13,0X1038);   
        delay_ms(40);   
        LCD_WriteReg(0X12,0X0012);//16    
        delay_ms(40);   
          LCD_WriteReg(0X10,0X3420);   
         LCD_WriteReg(0X13,0X3038);   
        delay_ms(70);   
        LCD_WriteReg(0X30,0X0000);   
        LCD_WriteReg(0X31,0X0402);   
        LCD_WriteReg(0X32,0X0307);   
        LCD_WriteReg(0X33,0X0304);   
        LCD_WriteReg(0X34,0X0004);   
        LCD_WriteReg(0X35,0X0401);   
        LCD_WriteReg(0X36,0X0707);   
        LCD_WriteReg(0X37,0X0305);   
        LCD_WriteReg(0X38,0X0610);   
        LCD_WriteReg(0X39,0X0610); 
          
        LCD_WriteReg(0X01,0X0100);   
        LCD_WriteReg(0X02,0X0300);   
        LCD_WriteReg(0X03,0X1030);//改变方向的   
        LCD_WriteReg(0X08,0X0808);   
        LCD_WriteReg(0X0A,0X0008);   
         LCD_WriteReg(0X60,0X2700);   
        LCD_WriteReg(0X61,0X0001);   
        LCD_WriteReg(0X90,0X013E);   
        LCD_WriteReg(0X92,0X0100);   
        LCD_WriteReg(0X93,0X0100);   
         LCD_WriteReg(0XA0,0X3000);   
         LCD_WriteReg(0XA3,0X0010);   
        LCD_WriteReg(0X07,0X0001);   
        LCD_WriteReg(0X07,0X0021);   
        LCD_WriteReg(0X07,0X0023);   
        LCD_WriteReg(0X07,0X0033);   
        LCD_WriteReg(0X07,0X0133);   
    }else if(lcddev.id==0X1963)
    {
        LCD_WR_REG(0xE2);        //Set PLL with OSC = 10MHz (hardware),    Multiplier N = 35, 250MHz < VCO < 800MHz = OSC*(N+1), VCO = 300MHz
        LCD_WR_DATA(0x1D);        //参数1 
        LCD_WR_DATA(0x02);        //参数2 Divider M = 2, PLL = 300/(M+1) = 100MHz
        LCD_WR_DATA(0x04);        //参数3 Validate M and N values   
        delay_us(100);
        LCD_WR_REG(0xE0);        // Start PLL command
        LCD_WR_DATA(0x01);        // enable PLL
        delay_ms(10);
        LCD_WR_REG(0xE0);        // Start PLL command again
        LCD_WR_DATA(0x03);        // now, use PLL output as system clock    
        delay_ms(12);  
        LCD_WR_REG(0x01);        //软复位
        delay_ms(10);
        
        LCD_WR_REG(0xE6);        //设置像素频率,33Mhz
        LCD_WR_DATA(0x2F);
        LCD_WR_DATA(0xFF);
        LCD_WR_DATA(0xFF);
        
        LCD_WR_REG(0xB0);        //设置LCD模式
        LCD_WR_DATA(0x20);        //24位模式
        LCD_WR_DATA(0x00);        //TFT 模式 
    
        LCD_WR_DATA((SSD_HOR_RESOLUTION-1)>>8);//设置LCD水平像素
        LCD_WR_DATA(SSD_HOR_RESOLUTION-1);         
        LCD_WR_DATA((SSD_VER_RESOLUTION-1)>>8);//设置LCD垂直像素
        LCD_WR_DATA(SSD_VER_RESOLUTION-1);         
        LCD_WR_DATA(0x00);        //RGB序列 
        
        LCD_WR_REG(0xB4);        //Set horizontal period
        LCD_WR_DATA((SSD_HT-1)>>8);
        LCD_WR_DATA(SSD_HT-1);
        LCD_WR_DATA(SSD_HPS>>8);
        LCD_WR_DATA(SSD_HPS);
        LCD_WR_DATA(SSD_HOR_PULSE_WIDTH-1);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        LCD_WR_REG(0xB6);        //Set vertical period
        LCD_WR_DATA((SSD_VT-1)>>8);
        LCD_WR_DATA(SSD_VT-1);
        LCD_WR_DATA(SSD_VPS>>8);
        LCD_WR_DATA(SSD_VPS);
        LCD_WR_DATA(SSD_VER_FRONT_PORCH-1);
        LCD_WR_DATA(0x00);
        LCD_WR_DATA(0x00);
        
        LCD_WR_REG(0xF0);    //设置SSD1963与CPU接口为16bit  
        LCD_WR_DATA(0x03);    //16-bit(565 format) data for 16bpp 

        LCD_WR_REG(0x29);    //开启显示
        //设置PWM输出  背光通过占空比可调 
        LCD_WR_REG(0xD0);    //设置自动白平衡DBC
        LCD_WR_DATA(0x00);    //disable
    
        LCD_WR_REG(0xBE);    //配置PWM输出
        LCD_WR_DATA(0x05);    //1设置PWM频率
        LCD_WR_DATA(0xFE);    //2设置PWM占空比
        LCD_WR_DATA(0x01);    //3设置C
        LCD_WR_DATA(0x00);    //4设置D
        LCD_WR_DATA(0x00);    //5设置E 
        LCD_WR_DATA(0x00);    //6设置F 
        
        LCD_WR_REG(0xB8);    //设置GPIO配置
        LCD_WR_DATA(0x03);    //2个IO口设置成输出
        LCD_WR_DATA(0x01);    //GPIO使用正常的IO功能 
        LCD_WR_REG(0xBA);
        LCD_WR_DATA(0X01);    //GPIO[1:0]=01,控制LCD方向
        
        LCD_SSD_BackLightSet(100);//背光设置为最亮
    }         
    LCD_Display_Dir(1);        //EMWIN实验默认设置为横屏
    LCD_LED=1;                //点亮背光
    LCD_Clear(WHITE);
}  
//清屏函数
//color:要清屏的填充色
void LCD_Clear(u16 color)
{
    u32 index=0;      
    u32 totalpoint=lcddev.width;
    totalpoint*=lcddev.height;             //得到总点数
    if((lcddev.id==0X6804)&&(lcddev.dir==1))//6804横屏的时候特殊处理  
    {                            
         lcddev.dir=0;     
         lcddev.setxcmd=0X2A;
        lcddev.setycmd=0X2B;                   
        LCD_SetCursor(0x00,0x0000);        //设置光标位置  
         lcddev.dir=1;     
          lcddev.setxcmd=0X2B;
        lcddev.setycmd=0X2A;       
     }else LCD_SetCursor(0x00,0x0000);    //设置光标位置 
    LCD_WriteRAM_Prepare();             //开始写入GRAM           
    for(index=0;index<totalpoint;index++)
    {
        TFTLCD->LCD_RAM=color;    
    }
}  
//在指定区域内填充单个颜色
//(sx,sy),(ex,ey):填充矩形对角坐标,区域大小为:(ex-sx+1)*(ey-sy+1)   
//color:要填充的颜色
void LCD_Fill(u16 sx,u16 sy,u16 ex,u16 ey,u16 color)
{          
    u16 i,j;
    u16 xlen=0;
    u16 temp;
    if((lcddev.id==0X6804)&&(lcddev.dir==1))    //6804横屏的时候特殊处理  
    {
        temp=sx;
        sx=sy;
        sy=lcddev.width-ex-1;      
        ex=ey;
        ey=lcddev.width-temp-1;
         lcddev.dir=0;     
         lcddev.setxcmd=0X2A;
        lcddev.setycmd=0X2B;                   
        LCD_Fill(sx,sy,ex,ey,color);  
         lcddev.dir=1;     
          lcddev.setxcmd=0X2B;
        lcddev.setycmd=0X2A;       
     }else
    {
        xlen=ex-sx+1;     
        for(i=sy;i<=ey;i++)
        {
             LCD_SetCursor(sx,i);                      //设置光标位置 
            LCD_WriteRAM_Prepare();                 //开始写入GRAM      
            for(j=0;j<xlen;j++)TFTLCD->LCD_RAM=color;    //显示颜色         
        }
    }     
}  
//在指定区域内填充指定颜色块             
//(sx,sy),(ex,ey):填充矩形对角坐标,区域大小为:(ex-sx+1)*(ey-sy+1)   
//color:要填充的颜色
void LCD_Color_Fill(u16 sx,u16 sy,u16 ex,u16 ey,u16 *color)
{  
    u16 height,width;
    u16 i,j;
    width=ex-sx+1;             //得到填充的宽度
    height=ey-sy+1;            //高度
     for(i=0;i<height;i++)
    {
         LCD_SetCursor(sx,sy+i);       //设置光标位置 
        LCD_WriteRAM_Prepare();     //开始写入GRAM
        for(j=0;j<width;j++)TFTLCD->LCD_RAM=color[i*width+j];//写入数据 
    }          
}  
//画线
//x1,y1:起点坐标
//x2,y2:终点坐标  
void LCD_DrawLine(u16 x1, u16 y1, u16 x2, u16 y2)
{
    u16 t; 
    int xerr=0,yerr=0,delta_x,delta_y,distance; 
    int incx,incy,uRow,uCol; 
    delta_x=x2-x1; //计算坐标增量 
    delta_y=y2-y1; 
    uRow=x1; 
    uCol=y1; 
    if(delta_x>0)incx=1; //设置单步方向 
    else if(delta_x==0)incx=0;//垂直线 
    else {incx=-1;delta_x=-delta_x;} 
    if(delta_y>0)incy=1; 
    else if(delta_y==0)incy=0;//水平线 
    else{incy=-1;delta_y=-delta_y;} 
    if( delta_x>delta_y)distance=delta_x; //选取基本增量坐标轴 
    else distance=delta_y; 
    for(t=0;t<=distance+1;t++ )//画线输出 
    {  
        LCD_DrawPoint(uRow,uCol);//画点 
        xerr+=delta_x ; 
        yerr+=delta_y ; 
        if(xerr>distance) 
        { 
            xerr-=distance; 
            uRow+=incx; 
        } 
        if(yerr>distance) 
        { 
            yerr-=distance; 
            uCol+=incy; 
        } 
    }  
}    
//画矩形      
//(x1,y1),(x2,y2):矩形的对角坐标
void LCD_DrawRectangle(u16 x1, u16 y1, u16 x2, u16 y2)
{
    LCD_DrawLine(x1,y1,x2,y1);
    LCD_DrawLine(x1,y1,x1,y2);
    LCD_DrawLine(x1,y2,x2,y2);
    LCD_DrawLine(x2,y1,x2,y2);
}
//在指定位置画一个指定大小的圆
//(x,y):中心点
//r    :半径
void LCD_Draw_Circle(u16 x0,u16 y0,u8 r)
{
    int a,b;
    int di;
    a=0;b=r;      
    di=3-(r<<1);             //判断下个点位置的标志
    while(a<=b)
    {
        LCD_DrawPoint(x0+a,y0-b);             //5
         LCD_DrawPoint(x0+b,y0-a);             //0           
        LCD_DrawPoint(x0+b,y0+a);             //4               
        LCD_DrawPoint(x0+a,y0+b);             //6 
        LCD_DrawPoint(x0-a,y0+b);             //1       
         LCD_DrawPoint(x0-b,y0+a);             
        LCD_DrawPoint(x0-a,y0-b);             //2             
          LCD_DrawPoint(x0-b,y0-a);             //7                  
        a++;
        //使用Bresenham算法画圆     
        if(di<0)di +=4*a+6;      
        else
        {
            di+=10+4*(a-b);   
            b--;
        }                             
    }
}                                       
//在指定位置显示一个字符
//x,y:起始坐标
//num:要显示的字符:" "--->"~"
//size:字体大小 12/16/24
//mode:叠加方式(1)还是非叠加方式(0)
void LCD_ShowChar(u16 x,u16 y,u8 num,u8 size,u8 mode)
{                                
    u8 temp,t1,t;
    u16 y0=y;
    u8 csize=(size/8+((size%8)?1:0))*(size/2);        //得到字体一个字符对应点阵集所占的字节数    
     num=num-' ';//得到偏移后的值（ASCII字库是从空格开始取模，所以-' '就是对应字符的字库）
    for(t=0;t<csize;t++)
    {   
        if(size==12)temp=asc2_1206[num][t];          //调用1206字体
        else if(size==16)temp=asc2_1608[num][t];    //调用1608字体
        else if(size==24)temp=asc2_2412[num][t];    //调用2412字体
        else return;                                //没有的字库
        for(t1=0;t1<8;t1++)
        {                
            if(temp&0x80)LCD_Fast_DrawPoint(x,y,POINT_COLOR);
            else if(mode==0)LCD_Fast_DrawPoint(x,y,BACK_COLOR);
            temp<<=1;
            y++;
            if(y>=lcddev.height)return;        //超区域了
            if((y-y0)==size)
            {
                y=y0;
                x++;
                if(x>=lcddev.width)return;    //超区域了
                break;
            }
        }       
    }                            
}   
//m^n函数
//返回值:m^n次方.
u32 LCD_Pow(u8 m,u8 n)
{
    u32 result=1;     
    while(n--)result*=m;    
    return result;
}             
//显示数字,高位为0,则不显示
//x,y :起点坐标     
//len :数字的位数
//size:字体大小
//color:颜色 
//num:数值(0~4294967295);     
void LCD_ShowNum(u16 x,u16 y,u32 num,u8 len,u8 size)
{             
    u8 t,temp;
    u8 enshow=0;                           
    for(t=0;t<len;t++)
    {
        temp=(num/LCD_Pow(10,len-t-1))%10;
        if(enshow==0&&t<(len-1))
        {
            if(temp==0)
            {
                LCD_ShowChar(x+(size/2)*t,y,' ',size,0);
                continue;
            }else enshow=1; 
              
        }
         LCD_ShowChar(x+(size/2)*t,y,temp+'0',size,0); 
    }
} 
//显示数字,高位为0,还是显示
//x,y:起点坐标
//num:数值(0~999999999);     
//len:长度(即要显示的位数)
//size:字体大小
//mode:
//[7]:0,不填充;1,填充0.
//[6:1]:保留
//[0]:0,非叠加显示;1,叠加显示.
void LCD_ShowxNum(u16 x,u16 y,u32 num,u8 len,u8 size,u8 mode)
{  
    u8 t,temp;
    u8 enshow=0;                           
    for(t=0;t<len;t++)
    {
        temp=(num/LCD_Pow(10,len-t-1))%10;
        if(enshow==0&&t<(len-1))
        {
            if(temp==0)
            {
                if(mode&0X80)LCD_ShowChar(x+(size/2)*t,y,'0',size,mode&0X01);  
                else LCD_ShowChar(x+(size/2)*t,y,' ',size,mode&0X01);  
                 continue;
            }else enshow=1; 
              
        }
         LCD_ShowChar(x+(size/2)*t,y,temp+'0',size,mode&0X01); 
    }
} 
//显示字符串
//x,y:起点坐标
//width,height:区域大小  
//size:字体大小
//*p:字符串起始地址          
void LCD_ShowString(u16 x,u16 y,u16 width,u16 height,u8 size,u8 *p)
{         
    u8 x0=x;
    width+=x;
    height+=y;
    while((*p<='~')&&(*p>=' '))//判断是不是非法字符!
    {       
        if(x>=width){x=x0;y+=size;}
        if(y>=height)break;//退出
        LCD_ShowChar(x,y,*p,size,0);
        x+=size/2;
        p++;
    }  
}

View Code

#ifndef __FONT_H
#define __FONT_H        
//常用ASCII表
//偏移量32 
//ASCII字符集: !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~
//PC2LCD2002取模方式设置：阴码+逐列式+顺向+C51格式
//总共：3个字符集（12*12、16*16和24*24），用户可以自行新增其他分辨率的字符集。
//每个字符所占用的字节数为:(size/8+((size%8)?1:0))*(size/2),其中size:是字库生成时的点阵大小(12/16/24...)
 
//12*12 ASCII字符集点阵
const unsigned char asc2_1206[95][12]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x3F,0x40,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x30,0x00,0x40,0x00,0x30,0x00,0x40,0x00,0x00,0x00},/*""",2*/
{0x09,0x00,0x0B,0xC0,0x3D,0x00,0x0B,0xC0,0x3D,0x00,0x09,0x00},/*"#",3*/
{0x18,0xC0,0x24,0x40,0x7F,0xE0,0x22,0x40,0x31,0x80,0x00,0x00},/*"$",4*/
{0x18,0x00,0x24,0xC0,0x1B,0x00,0x0D,0x80,0x32,0x40,0x01,0x80},/*"%",5*/
{0x03,0x80,0x1C,0x40,0x27,0x40,0x1C,0x80,0x07,0x40,0x00,0x40},/*"&",6*/
{0x10,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x80,0x20,0x40,0x40,0x20},/*"(",8*/
{0x00,0x00,0x40,0x20,0x20,0x40,0x1F,0x80,0x00,0x00,0x00,0x00},/*")",9*/
{0x09,0x00,0x06,0x00,0x1F,0x80,0x06,0x00,0x09,0x00,0x00,0x00},/*"*",10*/
{0x04,0x00,0x04,0x00,0x3F,0x80,0x04,0x00,0x04,0x00,0x00,0x00},/*"+",11*/
{0x00,0x10,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x20,0x01,0xC0,0x06,0x00,0x38,0x00,0x40,0x00,0x00,0x00},/*"/",15*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"0",16*/
{0x00,0x00,0x10,0x40,0x3F,0xC0,0x00,0x40,0x00,0x00,0x00,0x00},/*"1",17*/
{0x18,0xC0,0x21,0x40,0x22,0x40,0x24,0x40,0x18,0x40,0x00,0x00},/*"2",18*/
{0x10,0x80,0x20,0x40,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"3",19*/
{0x02,0x00,0x0D,0x00,0x11,0x00,0x3F,0xC0,0x01,0x40,0x00,0x00},/*"4",20*/
{0x3C,0x80,0x24,0x40,0x24,0x40,0x24,0x40,0x23,0x80,0x00,0x00},/*"5",21*/
{0x1F,0x80,0x24,0x40,0x24,0x40,0x34,0x40,0x03,0x80,0x00,0x00},/*"6",22*/
{0x30,0x00,0x20,0x00,0x27,0xC0,0x38,0x00,0x20,0x00,0x00,0x00},/*"7",23*/
{0x1B,0x80,0x24,0x40,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"8",24*/
{0x1C,0x00,0x22,0xC0,0x22,0x40,0x22,0x40,0x1F,0x80,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x08,0x40,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x04,0x60,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x04,0x00,0x0A,0x00,0x11,0x00,0x20,0x80,0x40,0x40},/*"<",28*/
{0x09,0x00,0x09,0x00,0x09,0x00,0x09,0x00,0x09,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x40,0x40,0x20,0x80,0x11,0x00,0x0A,0x00,0x04,0x00},/*">",30*/
{0x18,0x00,0x20,0x00,0x23,0x40,0x24,0x00,0x18,0x00,0x00,0x00},/*"?",31*/
{0x1F,0x80,0x20,0x40,0x27,0x40,0x29,0x40,0x1F,0x40,0x00,0x00},/*"@",32*/
{0x00,0x40,0x07,0xC0,0x39,0x00,0x0F,0x00,0x01,0xC0,0x00,0x40},/*"A",33*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x24,0x40,0x1B,0x80,0x00,0x00},/*"B",34*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x30,0x80,0x00,0x00},/*"C",35*/
{0x20,0x40,0x3F,0xC0,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"D",36*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x2E,0x40,0x30,0xC0,0x00,0x00},/*"E",37*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x2E,0x00,0x30,0x00,0x00,0x00},/*"F",38*/
{0x0F,0x00,0x10,0x80,0x20,0x40,0x22,0x40,0x33,0x80,0x02,0x00},/*"G",39*/
{0x20,0x40,0x3F,0xC0,0x04,0x00,0x04,0x00,0x3F,0xC0,0x20,0x40},/*"H",40*/
{0x20,0x40,0x20,0x40,0x3F,0xC0,0x20,0x40,0x20,0x40,0x00,0x00},/*"I",41*/
{0x00,0x60,0x20,0x20,0x20,0x20,0x3F,0xC0,0x20,0x00,0x20,0x00},/*"J",42*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x0B,0x00,0x30,0xC0,0x20,0x40},/*"K",43*/
{0x20,0x40,0x3F,0xC0,0x20,0x40,0x00,0x40,0x00,0x40,0x00,0xC0},/*"L",44*/
{0x3F,0xC0,0x3C,0x00,0x03,0xC0,0x3C,0x00,0x3F,0xC0,0x00,0x00},/*"M",45*/
{0x20,0x40,0x3F,0xC0,0x0C,0x40,0x23,0x00,0x3F,0xC0,0x20,0x00},/*"N",46*/
{0x1F,0x80,0x20,0x40,0x20,0x40,0x20,0x40,0x1F,0x80,0x00,0x00},/*"O",47*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x24,0x00,0x18,0x00,0x00,0x00},/*"P",48*/
{0x1F,0x80,0x21,0x40,0x21,0x40,0x20,0xE0,0x1F,0xA0,0x00,0x00},/*"Q",49*/
{0x20,0x40,0x3F,0xC0,0x24,0x40,0x26,0x00,0x19,0xC0,0x00,0x40},/*"R",50*/
{0x18,0xC0,0x24,0x40,0x24,0x40,0x22,0x40,0x31,0x80,0x00,0x00},/*"S",51*/
{0x30,0x00,0x20,0x40,0x3F,0xC0,0x20,0x40,0x30,0x00,0x00,0x00},/*"T",52*/
{0x20,0x00,0x3F,0x80,0x00,0x40,0x00,0x40,0x3F,0x80,0x20,0x00},/*"U",53*/
{0x20,0x00,0x3E,0x00,0x01,0xC0,0x07,0x00,0x38,0x00,0x20,0x00},/*"V",54*/
{0x38,0x00,0x07,0xC0,0x3C,0x00,0x07,0xC0,0x38,0x00,0x00,0x00},/*"W",55*/
{0x20,0x40,0x39,0xC0,0x06,0x00,0x39,0xC0,0x20,0x40,0x00,0x00},/*"X",56*/
{0x20,0x00,0x38,0x40,0x07,0xC0,0x38,0x40,0x20,0x00,0x00,0x00},/*"Y",57*/
{0x30,0x40,0x21,0xC0,0x26,0x40,0x38,0x40,0x20,0xC0,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x7F,0xE0,0x40,0x20,0x40,0x20,0x00,0x00},/*"[",59*/
{0x00,0x00,0x70,0x00,0x0C,0x00,0x03,0x80,0x00,0x40,0x00,0x00},/*"\",60*/
{0x00,0x00,0x40,0x20,0x40,0x20,0x7F,0xE0,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x20,0x00,0x40,0x00,0x20,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10},/*"_",63*/
{0x00,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x02,0x80,0x05,0x40,0x05,0x40,0x03,0xC0,0x00,0x40},/*"a",65*/
{0x20,0x00,0x3F,0xC0,0x04,0x40,0x04,0x40,0x03,0x80,0x00,0x00},/*"b",66*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x40,0x06,0x40,0x00,0x00},/*"c",67*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x24,0x40,0x3F,0xC0,0x00,0x40},/*"d",68*/
{0x00,0x00,0x03,0x80,0x05,0x40,0x05,0x40,0x03,0x40,0x00,0x00},/*"e",69*/
{0x00,0x00,0x04,0x40,0x1F,0xC0,0x24,0x40,0x24,0x40,0x20,0x00},/*"f",70*/
{0x00,0x00,0x02,0xE0,0x05,0x50,0x05,0x50,0x06,0x50,0x04,0x20},/*"g",71*/
{0x20,0x40,0x3F,0xC0,0x04,0x40,0x04,0x00,0x03,0xC0,0x00,0x40},/*"h",72*/
{0x00,0x00,0x04,0x40,0x27,0xC0,0x00,0x40,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x10,0x00,0x10,0x04,0x10,0x27,0xE0,0x00,0x00,0x00,0x00},/*"j",74*/
{0x20,0x40,0x3F,0xC0,0x01,0x40,0x07,0x00,0x04,0xC0,0x04,0x40},/*"k",75*/
{0x20,0x40,0x20,0x40,0x3F,0xC0,0x00,0x40,0x00,0x40,0x00,0x00},/*"l",76*/
{0x07,0xC0,0x04,0x00,0x07,0xC0,0x04,0x00,0x03,0xC0,0x00,0x00},/*"m",77*/
{0x04,0x40,0x07,0xC0,0x04,0x40,0x04,0x00,0x03,0xC0,0x00,0x40},/*"n",78*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x40,0x03,0x80,0x00,0x00},/*"o",79*/
{0x04,0x10,0x07,0xF0,0x04,0x50,0x04,0x40,0x03,0x80,0x00,0x00},/*"p",80*/
{0x00,0x00,0x03,0x80,0x04,0x40,0x04,0x50,0x07,0xF0,0x00,0x10},/*"q",81*/
{0x04,0x40,0x07,0xC0,0x02,0x40,0x04,0x00,0x04,0x00,0x00,0x00},/*"r",82*/
{0x00,0x00,0x06,0x40,0x05,0x40,0x05,0x40,0x04,0xC0,0x00,0x00},/*"s",83*/
{0x00,0x00,0x04,0x00,0x1F,0x80,0x04,0x40,0x00,0x40,0x00,0x00},/*"t",84*/
{0x04,0x00,0x07,0x80,0x00,0x40,0x04,0x40,0x07,0xC0,0x00,0x40},/*"u",85*/
{0x04,0x00,0x07,0x00,0x04,0xC0,0x01,0x80,0x06,0x00,0x04,0x00},/*"v",86*/
{0x06,0x00,0x01,0xC0,0x07,0x00,0x01,0xC0,0x06,0x00,0x00,0x00},/*"w",87*/
{0x04,0x40,0x06,0xC0,0x01,0x00,0x06,0xC0,0x04,0x40,0x00,0x00},/*"x",88*/
{0x04,0x10,0x07,0x10,0x04,0xE0,0x01,0x80,0x06,0x00,0x04,0x00},/*"y",89*/
{0x00,0x00,0x04,0x40,0x05,0xC0,0x06,0x40,0x04,0x40,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x04,0x00,0x7B,0xE0,0x40,0x20,0x00,0x00},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xF0,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x40,0x20,0x7B,0xE0,0x04,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x40,0x00,0x80,0x00,0x40,0x00,0x20,0x00,0x20,0x00,0x40,0x00},/*"~",94*/
};  
//16*16 ASCII字符集点阵
const unsigned char asc2_1608[95][16]={      
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0xCC,0x00,0x0C,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x08,0x00,0x30,0x00,0x60,0x00,0x08,0x00,0x30,0x00,0x60,0x00,0x00,0x00},/*""",2*/
{0x02,0x20,0x03,0xFC,0x1E,0x20,0x02,0x20,0x03,0xFC,0x1E,0x20,0x02,0x20,0x00,0x00},/*"#",3*/
{0x00,0x00,0x0E,0x18,0x11,0x04,0x3F,0xFF,0x10,0x84,0x0C,0x78,0x00,0x00,0x00,0x00},/*"$",4*/
{0x0F,0x00,0x10,0x84,0x0F,0x38,0x00,0xC0,0x07,0x78,0x18,0x84,0x00,0x78,0x00,0x00},/*"%",5*/
{0x00,0x78,0x0F,0x84,0x10,0xC4,0x11,0x24,0x0E,0x98,0x00,0xE4,0x00,0x84,0x00,0x08},/*"&",6*/
{0x08,0x00,0x68,0x00,0x70,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xE0,0x18,0x18,0x20,0x04,0x40,0x02,0x00,0x00},/*"(",8*/
{0x00,0x00,0x40,0x02,0x20,0x04,0x18,0x18,0x07,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*")",9*/
{0x02,0x40,0x02,0x40,0x01,0x80,0x0F,0xF0,0x01,0x80,0x02,0x40,0x02,0x40,0x00,0x00},/*"*",10*/
{0x00,0x80,0x00,0x80,0x00,0x80,0x0F,0xF8,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x00},/*"+",11*/
{0x00,0x01,0x00,0x0D,0x00,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80},/*"-",13*/
{0x00,0x00,0x00,0x0C,0x00,0x0C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x06,0x00,0x18,0x00,0x60,0x01,0x80,0x06,0x00,0x18,0x00,0x20,0x00},/*"/",15*/
{0x00,0x00,0x07,0xF0,0x08,0x08,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"0",16*/
{0x00,0x00,0x08,0x04,0x08,0x04,0x1F,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"1",17*/
{0x00,0x00,0x0E,0x0C,0x10,0x14,0x10,0x24,0x10,0x44,0x11,0x84,0x0E,0x0C,0x00,0x00},/*"2",18*/
{0x00,0x00,0x0C,0x18,0x10,0x04,0x11,0x04,0x11,0x04,0x12,0x88,0x0C,0x70,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0xE0,0x03,0x20,0x04,0x24,0x08,0x24,0x1F,0xFC,0x00,0x24,0x00,0x00},/*"4",20*/
{0x00,0x00,0x1F,0x98,0x10,0x84,0x11,0x04,0x11,0x04,0x10,0x88,0x10,0x70,0x00,0x00},/*"5",21*/
{0x00,0x00,0x07,0xF0,0x08,0x88,0x11,0x04,0x11,0x04,0x18,0x88,0x00,0x70,0x00,0x00},/*"6",22*/
{0x00,0x00,0x1C,0x00,0x10,0x00,0x10,0xFC,0x13,0x00,0x1C,0x00,0x10,0x00,0x00,0x00},/*"7",23*/
{0x00,0x00,0x0E,0x38,0x11,0x44,0x10,0x84,0x10,0x84,0x11,0x44,0x0E,0x38,0x00,0x00},/*"8",24*/
{0x00,0x00,0x07,0x00,0x08,0x8C,0x10,0x44,0x10,0x44,0x08,0x88,0x07,0xF0,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x0C,0x03,0x0C,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x00,0x80,0x01,0x40,0x02,0x20,0x04,0x10,0x08,0x08,0x10,0x04,0x00,0x00},/*"<",28*/
{0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x00,0x00},/*"=",29*/
{0x00,0x00,0x10,0x04,0x08,0x08,0x04,0x10,0x02,0x20,0x01,0x40,0x00,0x80,0x00,0x00},/*">",30*/
{0x00,0x00,0x0E,0x00,0x12,0x00,0x10,0x0C,0x10,0x6C,0x10,0x80,0x0F,0x00,0x00,0x00},/*"?",31*/
{0x03,0xE0,0x0C,0x18,0x13,0xE4,0x14,0x24,0x17,0xC4,0x08,0x28,0x07,0xD0,0x00,0x00},/*"@",32*/
{0x00,0x04,0x00,0x3C,0x03,0xC4,0x1C,0x40,0x07,0x40,0x00,0xE4,0x00,0x1C,0x00,0x04},/*"A",33*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x04,0x11,0x04,0x0E,0x88,0x00,0x70,0x00,0x00},/*"B",34*/
{0x03,0xE0,0x0C,0x18,0x10,0x04,0x10,0x04,0x10,0x04,0x10,0x08,0x1C,0x10,0x00,0x00},/*"C",35*/
{0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"D",36*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x04,0x17,0xC4,0x10,0x04,0x08,0x18,0x00,0x00},/*"E",37*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x00,0x17,0xC0,0x10,0x00,0x08,0x00,0x00,0x00},/*"F",38*/
{0x03,0xE0,0x0C,0x18,0x10,0x04,0x10,0x04,0x10,0x44,0x1C,0x78,0x00,0x40,0x00,0x00},/*"G",39*/
{0x10,0x04,0x1F,0xFC,0x10,0x84,0x00,0x80,0x00,0x80,0x10,0x84,0x1F,0xFC,0x10,0x04},/*"H",40*/
{0x00,0x00,0x10,0x04,0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x04,0x00,0x00,0x00,0x00},/*"I",41*/
{0x00,0x03,0x00,0x01,0x10,0x01,0x10,0x01,0x1F,0xFE,0x10,0x00,0x10,0x00,0x00,0x00},/*"J",42*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x03,0x80,0x14,0x64,0x18,0x1C,0x10,0x04,0x00,0x00},/*"K",43*/
{0x10,0x04,0x1F,0xFC,0x10,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x0C,0x00,0x00},/*"L",44*/
{0x10,0x04,0x1F,0xFC,0x1F,0x00,0x00,0xFC,0x1F,0x00,0x1F,0xFC,0x10,0x04,0x00,0x00},/*"M",45*/
{0x10,0x04,0x1F,0xFC,0x0C,0x04,0x03,0x00,0x00,0xE0,0x10,0x18,0x1F,0xFC,0x10,0x00},/*"N",46*/
{0x07,0xF0,0x08,0x08,0x10,0x04,0x10,0x04,0x10,0x04,0x08,0x08,0x07,0xF0,0x00,0x00},/*"O",47*/
{0x10,0x04,0x1F,0xFC,0x10,0x84,0x10,0x80,0x10,0x80,0x10,0x80,0x0F,0x00,0x00,0x00},/*"P",48*/
{0x07,0xF0,0x08,0x18,0x10,0x24,0x10,0x24,0x10,0x1C,0x08,0x0A,0x07,0xF2,0x00,0x00},/*"Q",49*/
{0x10,0x04,0x1F,0xFC,0x11,0x04,0x11,0x00,0x11,0xC0,0x11,0x30,0x0E,0x0C,0x00,0x04},/*"R",50*/
{0x00,0x00,0x0E,0x1C,0x11,0x04,0x10,0x84,0x10,0x84,0x10,0x44,0x1C,0x38,0x00,0x00},/*"S",51*/
{0x18,0x00,0x10,0x00,0x10,0x04,0x1F,0xFC,0x10,0x04,0x10,0x00,0x18,0x00,0x00,0x00},/*"T",52*/
{0x10,0x00,0x1F,0xF8,0x10,0x04,0x00,0x04,0x00,0x04,0x10,0x04,0x1F,0xF8,0x10,0x00},/*"U",53*/
{0x10,0x00,0x1E,0x00,0x11,0xE0,0x00,0x1C,0x00,0x70,0x13,0x80,0x1C,0x00,0x10,0x00},/*"V",54*/
{0x1F,0xC0,0x10,0x3C,0x00,0xE0,0x1F,0x00,0x00,0xE0,0x10,0x3C,0x1F,0xC0,0x00,0x00},/*"W",55*/
{0x10,0x04,0x18,0x0C,0x16,0x34,0x01,0xC0,0x01,0xC0,0x16,0x34,0x18,0x0C,0x10,0x04},/*"X",56*/
{0x10,0x00,0x1C,0x00,0x13,0x04,0x00,0xFC,0x13,0x04,0x1C,0x00,0x10,0x00,0x00,0x00},/*"Y",57*/
{0x08,0x04,0x10,0x1C,0x10,0x64,0x10,0x84,0x13,0x04,0x1C,0x04,0x10,0x18,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0xFE,0x40,0x02,0x40,0x02,0x40,0x02,0x00,0x00},/*"[",59*/
{0x00,0x00,0x30,0x00,0x0C,0x00,0x03,0x80,0x00,0x60,0x00,0x1C,0x00,0x03,0x00,0x00},/*"\",60*/
{0x00,0x00,0x40,0x02,0x40,0x02,0x40,0x02,0x7F,0xFE,0x00,0x00,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x00,0x00},/*"^",62*/
{0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01},/*"_",63*/
{0x00,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x98,0x01,0x24,0x01,0x44,0x01,0x44,0x01,0x44,0x00,0xFC,0x00,0x04},/*"a",65*/
{0x10,0x00,0x1F,0xFC,0x00,0x88,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x70,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x11,0x08,0x1F,0xFC,0x00,0x04},/*"d",68*/
{0x00,0x00,0x00,0xF8,0x01,0x44,0x01,0x44,0x01,0x44,0x01,0x44,0x00,0xC8,0x00,0x00},/*"e",69*/
{0x00,0x00,0x01,0x04,0x01,0x04,0x0F,0xFC,0x11,0x04,0x11,0x04,0x11,0x00,0x18,0x00},/*"f",70*/
{0x00,0x00,0x00,0xD6,0x01,0x29,0x01,0x29,0x01,0x29,0x01,0xC9,0x01,0x06,0x00,0x00},/*"g",71*/
{0x10,0x04,0x1F,0xFC,0x00,0x84,0x01,0x00,0x01,0x00,0x01,0x04,0x00,0xFC,0x00,0x04},/*"h",72*/
{0x00,0x00,0x01,0x04,0x19,0x04,0x19,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x03,0x00,0x01,0x01,0x01,0x19,0x01,0x19,0xFE,0x00,0x00,0x00,0x00},/*"j",74*/
{0x10,0x04,0x1F,0xFC,0x00,0x24,0x00,0x40,0x01,0xB4,0x01,0x0C,0x01,0x04,0x00,0x00},/*"k",75*/
{0x00,0x00,0x10,0x04,0x10,0x04,0x1F,0xFC,0x00,0x04,0x00,0x04,0x00,0x00,0x00,0x00},/*"l",76*/
{0x01,0x04,0x01,0xFC,0x01,0x04,0x01,0x00,0x01,0xFC,0x01,0x04,0x01,0x00,0x00,0xFC},/*"m",77*/
{0x01,0x04,0x01,0xFC,0x00,0x84,0x01,0x00,0x01,0x00,0x01,0x04,0x00,0xFC,0x00,0x04},/*"n",78*/
{0x00,0x00,0x00,0xF8,0x01,0x04,0x01,0x04,0x01,0x04,0x01,0x04,0x00,0xF8,0x00,0x00},/*"o",79*/
{0x01,0x01,0x01,0xFF,0x00,0x85,0x01,0x04,0x01,0x04,0x00,0x88,0x00,0x70,0x00,0x00},/*"p",80*/
{0x00,0x00,0x00,0x70,0x00,0x88,0x01,0x04,0x01,0x04,0x01,0x05,0x01,0xFF,0x00,0x01},/*"q",81*/
{0x01,0x04,0x01,0x04,0x01,0xFC,0x00,0x84,0x01,0x04,0x01,0x00,0x01,0x80,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0xCC,0x01,0x24,0x01,0x24,0x01,0x24,0x01,0x24,0x01,0x98,0x00,0x00},/*"s",83*/
{0x00,0x00,0x01,0x00,0x01,0x00,0x07,0xF8,0x01,0x04,0x01,0x04,0x00,0x00,0x00,0x00},/*"t",84*/
{0x01,0x00,0x01,0xF8,0x00,0x04,0x00,0x04,0x00,0x04,0x01,0x08,0x01,0xFC,0x00,0x04},/*"u",85*/
{0x01,0x00,0x01,0x80,0x01,0x70,0x00,0x0C,0x00,0x10,0x01,0x60,0x01,0x80,0x01,0x00},/*"v",86*/
{0x01,0xF0,0x01,0x0C,0x00,0x30,0x01,0xC0,0x00,0x30,0x01,0x0C,0x01,0xF0,0x01,0x00},/*"w",87*/
{0x00,0x00,0x01,0x04,0x01,0x8C,0x00,0x74,0x01,0x70,0x01,0x8C,0x01,0x04,0x00,0x00},/*"x",88*/
{0x01,0x01,0x01,0x81,0x01,0x71,0x00,0x0E,0x00,0x18,0x01,0x60,0x01,0x80,0x01,0x00},/*"y",89*/
{0x00,0x00,0x01,0x84,0x01,0x0C,0x01,0x34,0x01,0x44,0x01,0x84,0x01,0x0C,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x3E,0xFC,0x40,0x02,0x40,0x02},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x40,0x02,0x40,0x02,0x3E,0xFC,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x00,0x60,0x00,0x80,0x00,0x80,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x20,0x00},/*"~",94*/
};  
//24*24 ASICII字符集点阵
const unsigned char asc2_2412[95][36]={      
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x80,0x38,0x0F,0xFE,0x38,0x0F,0x80,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x00,0x06,0x00,0x00,0x0C,0x00,0x00,0x38,0x00,0x00,0x31,0x00,0x00,0x06,0x00,0x00,0x0C,0x00,0x00,0x38,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x00,0x00,0x00,0x61,0x80,0x00,0x67,0xF8,0x07,0xF9,0x80,0x00,0x61,0x80,0x00,0x61,0x80,0x00,0x61,0x80,0x00,0x61,0x80,0x00,0x67,0xF8,0x07,0xF9,0x80,0x00,0x61,0x80,0x00,0x00,0x00},/*"#",3*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xC0,0xE0,0x03,0xE0,0xF0,0x06,0x30,0x08,0x04,0x18,0x08,0x1F,0xFF,0xFE,0x04,0x0E,0x08,0x07,0x87,0xF0,0x03,0x81,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*"$",4*/
{0x01,0xF0,0x00,0x06,0x0C,0x00,0x04,0x04,0x08,0x06,0x0C,0x70,0x01,0xF9,0xC0,0x00,0x0E,0x00,0x00,0x3B,0xE0,0x00,0xEC,0x18,0x07,0x08,0x08,0x04,0x0C,0x18,0x00,0x03,0xE0,0x00,0x00,0x00},/*"%",5*/
{0x00,0x01,0xE0,0x00,0x07,0xF0,0x03,0xF8,0x18,0x04,0x1C,0x08,0x04,0x17,0x08,0x07,0xE1,0xD0,0x03,0xC0,0xE0,0x00,0x23,0xB0,0x00,0x3C,0x08,0x00,0x20,0x08,0x00,0x00,0x10,0x00,0x00,0x00},/*"&",6*/
{0x00,0x00,0x00,0x01,0x00,0x00,0x31,0x00,0x00,0x32,0x00,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x01,0xFF,0xC0,0x07,0x80,0xF0,0x0C,0x00,0x18,0x10,0x00,0x04,0x20,0x00,0x02,0x00,0x00,0x00},/*"(",8*/
{0x00,0x00,0x00,0x20,0x00,0x02,0x10,0x00,0x04,0x0C,0x00,0x18,0x07,0x80,0xF0,0x01,0xFF,0xC0,0x00,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*")",9*/
{0x00,0x00,0x00,0x00,0x42,0x00,0x00,0x66,0x00,0x00,0x66,0x00,0x00,0x3C,0x00,0x00,0x18,0x00,0x03,0xFF,0xC0,0x00,0x18,0x00,0x00,0x3C,0x00,0x00,0x66,0x00,0x00,0x66,0x00,0x00,0x42,0x00},/*"*",10*/
{0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x01,0xFF,0xC0,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x00,0x31,0x00,0x00,0x32,0x00,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x00,0x00,0x38,0x00,0x00,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x00,0x1C,0x00,0x00,0x70,0x00,0x01,0x80,0x00,0x0E,0x00,0x00,0x38,0x00,0x00,0xC0,0x00,0x07,0x00,0x00,0x1C,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00},/*"/",15*/
{0x00,0x00,0x00,0x00,0x7F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x18,0x04,0x00,0x08,0x04,0x00,0x08,0x06,0x00,0x18,0x03,0x80,0x70,0x01,0xFF,0xE0,0x00,0x7F,0x80,0x00,0x00,0x00},/*"0",16*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x08,0x01,0x00,0x08,0x01,0x00,0x08,0x03,0xFF,0xF8,0x07,0xFF,0xF8,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"1",17*/
{0x00,0x00,0x00,0x01,0xC0,0x38,0x02,0xC0,0x58,0x04,0x00,0x98,0x04,0x01,0x18,0x04,0x02,0x18,0x04,0x04,0x18,0x06,0x1C,0x18,0x03,0xF8,0x18,0x01,0xE0,0xF8,0x00,0x00,0x00,0x00,0x00,0x00},/*"2",18*/
{0x00,0x00,0x00,0x01,0xC0,0xE0,0x03,0xC0,0xF0,0x04,0x00,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x06,0x18,0x08,0x03,0xF4,0x18,0x01,0xE7,0xF0,0x00,0x01,0xE0,0x00,0x00,0x00,0x00,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x0D,0x00,0x00,0x11,0x00,0x00,0x61,0x00,0x00,0x81,0x08,0x03,0x01,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x01,0x08,0x00,0x01,0x08,0x00,0x00,0x00},/*"4",20*/
{0x00,0x00,0x00,0x00,0x00,0xE0,0x07,0xFC,0xD0,0x06,0x08,0x08,0x06,0x10,0x08,0x06,0x10,0x08,0x06,0x10,0x08,0x06,0x18,0x38,0x06,0x0F,0xF0,0x06,0x07,0xC0,0x00,0x00,0x00,0x00,0x00,0x00},/*"5",21*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x01,0xFF,0xE0,0x03,0x84,0x30,0x02,0x08,0x18,0x04,0x10,0x08,0x04,0x10,0x08,0x04,0x10,0x08,0x07,0x18,0x10,0x03,0x0F,0xF0,0x00,0x07,0xC0,0x00,0x00,0x00},/*"6",22*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xC0,0x00,0x07,0x00,0x00,0x06,0x00,0x00,0x06,0x00,0xF8,0x06,0x07,0xF8,0x06,0x18,0x00,0x06,0xE0,0x00,0x07,0x00,0x00,0x06,0x00,0x00,0x00,0x00,0x00},/*"7",23*/
{0x00,0x00,0x00,0x01,0xE1,0xE0,0x03,0xF7,0xF0,0x06,0x34,0x10,0x04,0x18,0x08,0x04,0x18,0x08,0x04,0x0C,0x08,0x04,0x0C,0x08,0x06,0x16,0x18,0x03,0xF3,0xF0,0x01,0xC1,0xE0,0x00,0x00,0x00},/*"8",24*/
{0x00,0x00,0x00,0x00,0xF8,0x00,0x03,0xFC,0x30,0x03,0x06,0x38,0x04,0x02,0x08,0x04,0x02,0x08,0x04,0x02,0x08,0x04,0x04,0x10,0x03,0x08,0xF0,0x01,0xFF,0xC0,0x00,0x7F,0x00,0x00,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x38,0x00,0x70,0x38,0x00,0x70,0x38,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x1A,0x00,0x30,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x14,0x00,0x00,0x22,0x00,0x00,0x41,0x00,0x00,0x80,0x80,0x01,0x00,0x40,0x02,0x00,0x20,0x04,0x00,0x10,0x08,0x00,0x08,0x00,0x00,0x00},/*"<",28*/
{0x00,0x00,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x21,0x00,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x08,0x04,0x00,0x10,0x02,0x00,0x20,0x01,0x00,0x40,0x00,0x80,0x80,0x00,0x41,0x00,0x00,0x22,0x00,0x00,0x14,0x00,0x00,0x08,0x00,0x00,0x00,0x00},/*">",30*/
{0x00,0x00,0x00,0x03,0xC0,0x00,0x04,0xC0,0x00,0x04,0x00,0x00,0x08,0x00,0x38,0x08,0x0F,0x38,0x08,0x08,0x38,0x08,0x10,0x00,0x0C,0x30,0x00,0x07,0xE0,0x00,0x03,0xC0,0x00,0x00,0x00,0x00},/*"?",31*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x00,0xFF,0xE0,0x03,0x80,0x70,0x02,0x0F,0x10,0x06,0x70,0x88,0x04,0xC0,0x88,0x04,0x83,0x08,0x04,0x7F,0x88,0x02,0xC0,0x90,0x03,0x01,0x20,0x00,0xFE,0x40},/*"@",32*/
{0x00,0x00,0x08,0x00,0x00,0x18,0x00,0x01,0xF8,0x00,0x3E,0x08,0x01,0xC2,0x00,0x07,0x02,0x00,0x07,0xE2,0x00,0x00,0xFE,0x00,0x00,0x1F,0xC8,0x00,0x01,0xF8,0x00,0x00,0x38,0x00,0x00,0x08},/*"A",33*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x06,0x18,0x08,0x03,0xF4,0x18,0x01,0xE7,0xF0,0x00,0x01,0xE0,0x00,0x00,0x00},/*"B",34*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x02,0x00,0x18,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x10,0x06,0x00,0x20,0x07,0x80,0xC0,0x00,0x00,0x00},/*"C",35*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x18,0x02,0x00,0x10,0x03,0x80,0x70,0x01,0xFF,0xE0,0x00,0x7F,0x80,0x00,0x00,0x00},/*"D",36*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x08,0x08,0x04,0x3E,0x08,0x04,0x00,0x08,0x06,0x00,0x18,0x01,0x00,0x60,0x00,0x00,0x00},/*"E",37*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x00,0x04,0x08,0x00,0x04,0x08,0x00,0x04,0x3E,0x00,0x06,0x00,0x00,0x06,0x00,0x00,0x01,0x80,0x00,0x00,0x00,0x00},/*"F",38*/
{0x00,0x00,0x00,0x00,0x3F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x18,0x04,0x00,0x08,0x04,0x02,0x08,0x04,0x02,0x08,0x02,0x03,0xF0,0x07,0x83,0xF0,0x00,0x02,0x00,0x00,0x02,0x00},/*"G",39*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x04,0x08,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08},/*"H",40*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"I",41*/
{0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x00,0x07,0x00,0x00,0x01,0x04,0x00,0x01,0x04,0x00,0x01,0x04,0x00,0x03,0x07,0xFF,0xFE,0x07,0xFF,0xFC,0x04,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x00},/*"J",42*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x0C,0x08,0x00,0x18,0x00,0x00,0x3E,0x00,0x04,0xC7,0x80,0x05,0x03,0xC8,0x06,0x00,0xF8,0x04,0x00,0x38,0x04,0x00,0x18,0x00,0x00,0x08},/*"K",43*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x18,0x00,0x00,0x60,0x00,0x00,0x00},/*"L",44*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0x80,0x08,0x07,0xFC,0x00,0x00,0x7F,0xC0,0x00,0x03,0xF8,0x00,0x07,0xC0,0x00,0x78,0x00,0x07,0x80,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08},/*"M",45*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0x00,0x08,0x03,0xC0,0x00,0x00,0xE0,0x00,0x00,0x38,0x00,0x00,0x1E,0x00,0x00,0x07,0x00,0x00,0x01,0xC0,0x04,0x00,0xF0,0x07,0xFF,0xF8,0x04,0x00,0x00},/*"N",46*/
{0x00,0x00,0x00,0x00,0x7F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x18,0x04,0x00,0x08,0x04,0x00,0x08,0x06,0x00,0x18,0x03,0x00,0x30,0x01,0xFF,0xE0,0x00,0x7F,0x80,0x00,0x00,0x00},/*"O",47*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x04,0x08,0x04,0x04,0x00,0x04,0x04,0x00,0x04,0x04,0x00,0x04,0x04,0x00,0x06,0x0C,0x00,0x03,0xF8,0x00,0x01,0xF0,0x00,0x00,0x00,0x00},/*"P",48*/
{0x00,0x00,0x00,0x00,0x7F,0x80,0x01,0xFF,0xE0,0x03,0x80,0x70,0x06,0x00,0x88,0x04,0x00,0x88,0x04,0x00,0xC8,0x06,0x00,0x3C,0x03,0x00,0x3E,0x01,0xFF,0xE6,0x00,0x7F,0x84,0x00,0x00,0x00},/*"Q",49*/
{0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x08,0x08,0x04,0x08,0x00,0x04,0x0C,0x00,0x04,0x0F,0x00,0x04,0x0B,0xC0,0x06,0x10,0xF0,0x03,0xF0,0x38,0x01,0xE0,0x08,0x00,0x00,0x08},/*"R",50*/
{0x00,0x00,0x00,0x01,0xE0,0xF8,0x03,0xF0,0x30,0x06,0x30,0x10,0x04,0x18,0x08,0x04,0x18,0x08,0x04,0x0C,0x08,0x04,0x0C,0x08,0x02,0x06,0x18,0x02,0x07,0xF0,0x07,0x81,0xE0,0x00,0x00,0x00},/*"S",51*/
{0x01,0x80,0x00,0x06,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x08,0x07,0xFF,0xF8,0x07,0xFF,0xF8,0x04,0x00,0x08,0x04,0x00,0x00,0x04,0x00,0x00,0x06,0x00,0x00,0x01,0x80,0x00},/*"T",52*/
{0x04,0x00,0x00,0x07,0xFF,0xE0,0x07,0xFF,0xF0,0x04,0x00,0x18,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x04,0x00,0x10,0x07,0xFF,0xE0,0x04,0x00,0x00},/*"U",53*/
{0x04,0x00,0x00,0x06,0x00,0x00,0x07,0xE0,0x00,0x07,0xFE,0x00,0x04,0x1F,0xE0,0x00,0x01,0xF8,0x00,0x00,0x38,0x00,0x01,0xE0,0x04,0x3E,0x00,0x07,0xC0,0x00,0x06,0x00,0x00,0x04,0x00,0x00},/*"V",54*/
{0x04,0x00,0x00,0x07,0xE0,0x00,0x07,0xFF,0xC0,0x04,0x1F,0xF8,0x00,0x07,0xC0,0x07,0xF8,0x00,0x07,0xFF,0x80,0x04,0x3F,0xF8,0x00,0x07,0xC0,0x04,0xF8,0x00,0x07,0x00,0x00,0x04,0x00,0x00},/*"W",55*/
{0x00,0x00,0x00,0x04,0x00,0x08,0x06,0x00,0x18,0x07,0xC0,0x78,0x05,0xF1,0xC8,0x00,0x3E,0x00,0x00,0x1F,0x80,0x04,0x63,0xE8,0x07,0x80,0xF8,0x06,0x00,0x18,0x04,0x00,0x08,0x00,0x00,0x00},/*"X",56*/
{0x04,0x00,0x00,0x06,0x00,0x00,0x07,0x80,0x00,0x07,0xE0,0x08,0x04,0x7C,0x08,0x00,0x1F,0xF8,0x00,0x07,0xF8,0x00,0x18,0x08,0x04,0xE0,0x08,0x07,0x00,0x00,0x06,0x00,0x00,0x04,0x00,0x00},/*"Y",57*/
{0x00,0x00,0x00,0x01,0x00,0x08,0x06,0x00,0x38,0x04,0x00,0xF8,0x04,0x03,0xE8,0x04,0x0F,0x08,0x04,0x7C,0x08,0x05,0xF0,0x08,0x07,0xC0,0x08,0x07,0x00,0x18,0x04,0x00,0x60,0x00,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0xFF,0xFE,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x00,0x00,0x00},/*"[",59*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x07,0x00,0x00,0x00,0xC0,0x00,0x00,0x38,0x00,0x00,0x06,0x00,0x00,0x01,0xC0,0x00,0x00,0x30,0x00,0x00,0x0E,0x00,0x00,0x01,0x00,0x00,0x00},/*"\",60*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x20,0x00,0x02,0x3F,0xFF,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x10,0x00,0x00,0x30,0x00,0x00,0x20,0x00,0x00,0x30,0x00,0x00,0x10,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01,0x00,0x00,0x01},/*"_",63*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x10,0x00,0x00,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x19,0xF8,0x00,0x1B,0x18,0x00,0x22,0x08,0x00,0x26,0x08,0x00,0x24,0x08,0x00,0x24,0x10,0x00,0x3F,0xF8,0x00,0x1F,0xF8,0x00,0x00,0x08,0x00,0x00,0x18},/*"a",65*/
{0x00,0x00,0x00,0x04,0x00,0x00,0x07,0xFF,0xF8,0x0F,0xFF,0xF0,0x00,0x18,0x18,0x00,0x10,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x30,0x18,0x00,0x1F,0xF0,0x00,0x0F,0xC0,0x00,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x18,0x30,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x3C,0x08,0x00,0x1C,0x10,0x00,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x38,0x18,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x04,0x10,0x10,0x07,0xFF,0xF8,0x0F,0xFF,0xF0,0x00,0x00,0x10,0x00,0x00,0x00},/*"d",68*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x12,0x30,0x00,0x22,0x18,0x00,0x22,0x08,0x00,0x22,0x08,0x00,0x32,0x08,0x00,0x1E,0x10,0x00,0x0E,0x20,0x00,0x00,0x00},/*"e",69*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x20,0x08,0x00,0x20,0x08,0x01,0xFF,0xF8,0x03,0xFF,0xF8,0x06,0x20,0x08,0x04,0x20,0x08,0x04,0x20,0x08,0x07,0x20,0x00,0x03,0x00,0x00,0x00,0x00,0x00},/*"f",70*/
{0x00,0x00,0x00,0x00,0x00,0x0E,0x00,0x0E,0x6E,0x00,0x1F,0xF3,0x00,0x31,0xB1,0x00,0x20,0xB1,0x00,0x20,0xB1,0x00,0x31,0x91,0x00,0x1F,0x13,0x00,0x2E,0x1E,0x00,0x20,0x0E,0x00,0x30,0x00},/*"g",71*/
{0x00,0x00,0x00,0x04,0x00,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x10,0x08,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x1F,0xF8,0x00,0x00,0x08,0x00,0x00,0x00},/*"h",72*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x06,0x3F,0xF8,0x06,0x3F,0xF8,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x03,0x00,0x20,0x01,0x00,0x20,0x01,0x00,0x20,0x03,0x06,0x3F,0xFE,0x06,0x3F,0xFC,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"j",74*/
{0x00,0x00,0x00,0x04,0x00,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x01,0x88,0x00,0x03,0x00,0x00,0x2F,0xC0,0x00,0x38,0xF8,0x00,0x20,0x38,0x00,0x20,0x08,0x00,0x00,0x08,0x00,0x00,0x00},/*"k",75*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x08,0x04,0x00,0x08,0x04,0x00,0x08,0x07,0xFF,0xF8,0x0F,0xFF,0xF8,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00},/*"l",76*/
{0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x10,0x08,0x00,0x20,0x00,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x10,0x08,0x00,0x20,0x00,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x00,0x08},/*"m",77*/
{0x00,0x00,0x00,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x10,0x08,0x00,0x10,0x00,0x00,0x20,0x00,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x1F,0xF8,0x00,0x00,0x08,0x00,0x00,0x00},/*"n",78*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x0F,0xF0,0x00,0x18,0x30,0x00,0x30,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x30,0x08,0x00,0x18,0x30,0x00,0x0F,0xF0,0x00,0x07,0xC0,0x00,0x00,0x00},/*"o",79*/
{0x00,0x00,0x00,0x00,0x20,0x01,0x00,0x3F,0xFF,0x00,0x3F,0xFF,0x00,0x10,0x11,0x00,0x20,0x09,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x30,0x38,0x00,0x1F,0xF0,0x00,0x0F,0xC0,0x00,0x00,0x00},/*"p",80*/
{0x00,0x00,0x00,0x00,0x07,0xC0,0x00,0x1F,0xF0,0x00,0x38,0x18,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x09,0x00,0x10,0x11,0x00,0x1F,0xFF,0x00,0x3F,0xFF,0x00,0x00,0x01,0x00,0x00,0x00},/*"q",81*/
{0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x3F,0xF8,0x00,0x3F,0xF8,0x00,0x08,0x08,0x00,0x10,0x08,0x00,0x20,0x08,0x00,0x20,0x00,0x00,0x30,0x00,0x00,0x30,0x00,0x00,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x78,0x00,0x1E,0x18,0x00,0x33,0x08,0x00,0x23,0x08,0x00,0x21,0x08,0x00,0x21,0x88,0x00,0x21,0x98,0x00,0x30,0xF0,0x00,0x38,0x60,0x00,0x00,0x00},/*"s",83*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0xFF,0xF0,0x03,0xFF,0xF8,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x00,0x30,0x00,0x00,0x00,0x00,0x00,0x00},/*"t",84*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x3F,0xF0,0x00,0x7F,0xF8,0x00,0x00,0x18,0x00,0x00,0x08,0x00,0x00,0x08,0x00,0x20,0x10,0x00,0x3F,0xF8,0x00,0x7F,0xF0,0x00,0x00,0x10,0x00,0x00,0x00},/*"u",85*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x30,0x00,0x00,0x3C,0x00,0x00,0x3F,0x80,0x00,0x23,0xF0,0x00,0x00,0x78,0x00,0x00,0x70,0x00,0x23,0x80,0x00,0x3C,0x00,0x00,0x30,0x00,0x00,0x20,0x00},/*"v",86*/
{0x00,0x20,0x00,0x00,0x3C,0x00,0x00,0x3F,0xE0,0x00,0x23,0xF8,0x00,0x00,0xE0,0x00,0x27,0x00,0x00,0x3E,0x00,0x00,0x3F,0xE0,0x00,0x21,0xF8,0x00,0x01,0xE0,0x00,0x3E,0x00,0x00,0x20,0x00},/*"w",87*/
{0x00,0x00,0x00,0x00,0x20,0x08,0x00,0x20,0x08,0x00,0x38,0x38,0x00,0x3E,0x68,0x00,0x27,0x80,0x00,0x03,0xC8,0x00,0x2C,0xF8,0x00,0x38,0x38,0x00,0x20,0x18,0x00,0x20,0x08,0x00,0x00,0x00},/*"x",88*/
{0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x30,0x03,0x00,0x3C,0x01,0x00,0x3F,0x83,0x00,0x23,0xEC,0x00,0x00,0x70,0x00,0x23,0x80,0x00,0x3C,0x00,0x00,0x20,0x00,0x00,0x20,0x00,0x00,0x00,0x00},/*"y",89*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x08,0x00,0x20,0x38,0x00,0x20,0xF8,0x00,0x23,0xE8,0x00,0x2F,0x88,0x00,0x3E,0x08,0x00,0x38,0x08,0x00,0x20,0x18,0x00,0x00,0x70,0x00,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x14,0x00,0x1F,0xF7,0xFC,0x30,0x00,0x06,0x20,0x00,0x02,0x00,0x00,0x00,0x00,0x00,0x00},/*"{",91*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"|",92*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x02,0x30,0x00,0x06,0x1F,0xF7,0xFC,0x00,0x14,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x00,0x00,0x18,0x00,0x00,0x60,0x00,0x00,0x40,0x00,0x00,0x40,0x00,0x00,0x20,0x00,0x00,0x10,0x00,0x00,0x08,0x00,0x00,0x04,0x00,0x00,0x04,0x00,0x00,0x0C,0x00,0x00,0x10,0x00,0x00},/*"~",94*/
};      
#endif

View Code

免责声明！

本站转载的文章为个人学习借鉴使用，本站对版权不负任何法律责任。如果侵犯了您的隐私权益，请联系本站邮箱yoyou2525@163.com删除。

猜您在找 STM32 FSMC学习笔记+补充（LCD的FSMC配置） STM32F4—fsmc的配置步骤 stm32-FSMC的作用与功能 stm32库函数FSMC_NORSRAMInit()解析基于HAL库STM32的FSMC驱动8位TFTLCD屏 STM32F412--FSMC驱动TFTLCD 例程（一）基于通过STM32的FSMC总线读取FPGA的实现 stm32学习笔记--LCD1602显示 uCGUI 驱动LCD提速 STM32F主芯 STM32(十七)LCD 8080时序